openrcforums

Hello I have 2 XMTR modules I have issue 1 xmtr module not binding with RCVR. Other binds but is not working normal, red light stays off after removing bind cable and restart XMTR and RCVR. I opened both XMTR's and checked voltage regulator, big one, both are good. Circuit board is behind alu cover,...

Hello I have a Taranis X9D and my friend has a Taranis X9 lite. I use buddy box/ trainer and my XMTR is set as Master and his as Slave. I have it working but I have a question about settings in Slave XMTR- Tatranis X9 lite. In trainer mode I have selected replace when I switch over to student. If yo...

Hi If updated to 2.3.39, but if I want to Restore EEPROM I got message Directory is missing, same with Firmware. I downloaded SD card true companion, but I have this issue. Thanks for help Found problem :oops: I had still bootloader 2.0.9 in my Radio, after I changed bootloader to 2.3.9 I could do i...

Not sure why anyone would want to create a per cell sensor, but if you want to do that, yes, thats how you do it Hi Well if you want to know if a cell is going bad in a LIPO this a way to know which one. I f you fly yours LIPO's empty around 80% I know by experience you can see which cell is going ...

It is for the logfile as well. Again your 2.0 screenshot is useless for 2.1, things have completely changed. Hi After I found solution with my issue I know answer! In opentx2.1.10 in my case every item you wane have logged you must set a mark in the box Logs. Also you have to program every item you...

Update after I had some thinking and start a little bit fresh I flashed my Taranis to 2.1.10. Start over again with my telemetry settings and its indeed very different than 2.0.19. Anyway after some testing I found out how to do it, it's a lot more programming, and copy past for all the cell voltage...

Hi I understand what you're saying. But this is only for you taranis telemetry screen, but not for your logfile. You could see in my log file that cells 1-6 are logged, so this has nothing to do with yours screen data.... I did know about that, read it a while back. https://youtu.be/lORZGjDpZEg Rega...

Hi Guys What I'm trying to say all the time is... I use 2 sensors for my 10S-12S setup so I can log my cell voltage of my LIPO's It worked some times but know I can't get it working again. I used opentx 2.0.19 and even tried opentx 2.1.9. But now way I can see all cells in my log file, I even descri...

HI 3djc Thanks for yours reply. And of course I changed ID of sensors, if they have same ID it would not working. See pic below Here you can see they say ID: is 300 for both and instance is for one 6 and other 7!!! In Freelink you can see that physical ID is 6 and 7 and data rate is 300mS, very conf...

Hi

Thanks for answer bud I renamed logfile by adding a number behind logfile.
Put 1 and 2 behind it to separate files.
Could it be that one of my sensors has a fault when placed in daisy chain....

regards hans

Hi

I want to use 2 fvlss sensors.
I first used opentx2.0.19 and not working for 12s readout.
Second I tried opentx2.1.10 and also not working, even stranger things happening.

Hello Strange, I use Freelink and if I click on application ID it says default is 0.... Still not making sense to me. regards Hans Update I used freelink to set for both FLVSS application ID to "0" Same result only 5 cells are visible from my 10 cells setup????? Shoot me.... ;) regards Hans

Hi

Thanks for rely.
But at first I had application ID both at 0, and it didn't work also.
So....I tried several options but no results sadly.

Regards Hans

Hi I have taranis x9, with Opentx 2.0.19 I have 2 FLVSS daisy chained, one has ID5 and other has ID7. In Freelink you can assign also application ID, I set both to corresponding ID address. Well I had it worked at one time on and off it was.............., but most of the time it only reads out 1, mi...