Ailerons stuck on
Ailerons stuck on
Hi evryone. I seem to have no input into my ailerons. I was playing around with the settings/mixing and lost control of them. I got to the point where i did a Factory restore but it still did not fix the problem. I have the servos etc in the right way. When i go into the "display" screen the aileron bar is reading 100% but when i move the toggle the bar does not move (all other bars move when toggles are moved). Any thoughts on what has gone wrong?
Re: Ailerons stuck on
On which channel is your aileron connected, and what do you have on the mixer screen for that channel?
Re: Ailerons stuck on
ailerons are on 1 and by the mixer channel do you mean program mix?
Re: Ailerons stuck on
you have the stock firmware on your radio, right?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Ailerons stuck on
Ah. Moved to stock firmware section.
Re: Ailerons stuck on
how would i do that>>
Re: Ailerons stuck on
When i turn the flaperon from "INH" to "ACT" it changes the input. the display shows that if the flaperon is "INH" the ailerons are 100% but if the flaperon is "ACT" the ailerons are 0%. Either way though there is no bar movement on the "display" screen when the aileron toggle is moved. i was trying to set up the flaperons when the problem occured.
Re: Ailerons stuck on
Sorry, I know nothing about the stock firmware. Most here got rid of that quite quickly.
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Ailerons stuck on
Try posting your question here
http://www.rcgroups.com/forums/showthread.php?t=1035575
Dedicated to the stock firmware 9x.
Good luck
SM
ShowMaster
Sent from my iPod touch using Tapatalk
http://www.rcgroups.com/forums/showthread.php?t=1035575
Dedicated to the stock firmware 9x.
Good luck
SM
ShowMaster
Sent from my iPod touch using Tapatalk
Re: Ailerons stuck on
Can you change the 0% to 100 when it reads 0? That sounds like your problem.
-Gohst
Sent from my LG-P999 using Tapatalk 2
-Gohst
Sent from my LG-P999 using Tapatalk 2
-
- Posts: 4
- Joined: Sat Dec 08, 2012 12:41 pm
- Country: -
Re: Ailerons stuck on
I had somthing similar and it was a bad solder conection on the pot, weather was very cold and guess the contraction was enough to break the contact.
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Ailerons stuck on
I've had to repair several Turnigy TXs that came with water damage?
Switches and aux pots were not working or acting weird. Pot spray/lube fixed the pots and all new switches fixed the shorted or open switches, what a pain but good to go.
My ohm meter paid for itself because I couldn't believe they were all messed up at first.
SM
Switches and aux pots were not working or acting weird. Pot spray/lube fixed the pots and all new switches fixed the shorted or open switches, what a pain but good to go.
My ohm meter paid for itself because I couldn't believe they were all messed up at first.
SM