I have tried everything I know how to activate telemetry on my Turnigy 9Xtreme upgrade but I am not getting anywhere.
Where does the black/ white wire go on the XJT Tx Module ?
I have the smart port cable for my PixHawk connected.
Just not getting anything...
FrSky XJT Telemetry
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: FrSky XJT Telemetry
Black wire to S.Port on XJT module, see here: (viewtopic.php?f=126&t=7771).
You can also Black wire to pin 5 on the 9x back board. In Protocol setting are you using PXX protocol ?
Bob B.
You can also Black wire to pin 5 on the 9x back board. In Protocol setting are you using PXX protocol ?
Bob B.
Last edited by bob195558 on Fri Sep 09, 2016 4:58 pm, edited 4 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: FrSky XJT Telemetry
Yes, PXX protocol
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: FrSky XJT Telemetry
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: FrSky XJT Telemetry
I'm on it, just no good results.
I am getting a SWR reading but only after I switch from my 550 to my 450 and back to 550 models.
I am getting a SWR reading but only after I switch from my 550 to my 450 and back to 550 models.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: FrSky XJT Telemetry
I have not used S.Port telemetry data (cable connection) from a Flight Controller Board (PixHawk) to a 9x radio (using the XJT module).pmshop wrote: I have the smart port cable for my PixHawk connected.
Just not getting anything...
I am not able to help with this, but maybe someone else will know how and help you.
What FrSky receiver are you using ?
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: FrSky XJT Telemetry
X8Rbob195558 wrote: I have not used S.Port telemetry data (cable connection) from a Flight Controller Board (PixHawk) to a 9x radio (using the XJT module).
I am not able to help with this, but maybe someone else will know how and help you.
What FrSky receiver are you using ?
Bob B.
- MikeB
- 9x Developer
- Posts: 17996
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: FrSky XJT Telemetry
What revision of erksy9x are you using?
Once you are seeing a SWR value, go to the telemetry menu, step down to the Rx Voltage setting and set the value to 13.2V. The number on the right of the screen should then show the Rx voltage on the X8R, and you should also get a RSSI reading. Both of these come from the X8R.
Mike.
Once you are seeing a SWR value, go to the telemetry menu, step down to the Rx Voltage setting and set the value to 13.2V. The number on the right of the screen should then show the Rx voltage on the X8R, and you should also get a RSSI reading. Both of these come from the X8R.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: FrSky XJT Telemetry
V.494-Mike
13.08.2016
23:31:52
ersky9x-pr219
9XT
By the way, I noticed the coordinates are 4 digits before the decimal and not 2 digits Crazy thing is the Tx says I have no GPS signal but the numbers move when I move the craft.
I cannot pull in any other data even though I have the smart bus cable from the PixHawk to the X8R And it was connected per Craft & Theory's instructions...except for the Taranis part of course...
13.08.2016
23:31:52
ersky9x-pr219
9XT
By the way, I noticed the coordinates are 4 digits before the decimal and not 2 digits Crazy thing is the Tx says I have no GPS signal but the numbers move when I move the craft.
I cannot pull in any other data even though I have the smart bus cable from the PixHawk to the X8R And it was connected per Craft & Theory's instructions...except for the Taranis part of course...
- Attachments
-
- FlightDeck_Manual.pdf
- (2.32 MiB) Downloaded 317 times
Re: FrSky XJT Telemetry
Went here with my conversation since there is another guy with the same Tx setup issues
viewtopic.php?f=95&t=9164&p=118762#p118762
viewtopic.php?f=95&t=9164&p=118762#p118762