ok i dont know how to explain it but i would like to have this set up but i cant figure out how to do it
here is a link to the vid with it doing what i would like
http://www.youtube.com/watch?v=Fv9i-PkvzMk
thanks
jon
wanted this setup b-2 rudder
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: wanted this setup b-2 rudder
I did this on one of my models - but no longer have the hex for it!
It is not too complex.
Do you have 3 surfaces in total per wing?
So... elevator, aileron1, aileron2
Rob
Sent from my GT-I9300 using Tapatalk 2
It is not too complex.
Do you have 3 surfaces in total per wing?
So... elevator, aileron1, aileron2
Rob
Sent from my GT-I9300 using Tapatalk 2
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: wanted this setup b-2 rudder
i have 2 servos in each wing
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: wanted this setup b-2 rudder
Have you got aileron / elevator control working already?
Sent from my GT-I9300 using Tapatalk 2
Sent from my GT-I9300 using Tapatalk 2
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: wanted this setup b-2 rudder
yes i do have ale and elv working
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: wanted this setup b-2 rudder
Ok.... so you ate most of the way there!
Simply add in 4 mixes. One for each of the channels, setting the rudder stick as the input.
Adjust the weight to be -100 or 100 on each to get the direction right.
Sent from my GT-I9300 using Tapatalk 2
Simply add in 4 mixes. One for each of the channels, setting the rudder stick as the input.
Adjust the weight to be -100 or 100 on each to get the direction right.
Sent from my GT-I9300 using Tapatalk 2
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
-
- Posts: 5
- Joined: Mon Dec 01, 2014 5:17 am
- Country: -
Re: wanted this setup b-2 rudder
Actually this is not possible with only 2 servos per wing. If you do it with your current config of wing, you will get a hell of a lot of drag when deployed, with almost no rudder-effect, as the split of the counterworking sections are placed halfway in wing. It should be placed further out.
For better performance of the rudder, you need to split the aileron (which is placed in the right place for this) into 2 and add a servo for the added section. So then you have 3 servos pr. wing and can mix yourself a nice working drag-rudder B-2 style.
The mix goes like this:
Under both outer Ail channels/servos, you need one line with source iRud, weight 50%
Under both inner Ail-channels another line with source iRud, weight opposite above -50%
During full R-Rudder you should see this
For better performance of the rudder, you need to split the aileron (which is placed in the right place for this) into 2 and add a servo for the added section. So then you have 3 servos pr. wing and can mix yourself a nice working drag-rudder B-2 style.
The mix goes like this:
Under both outer Ail channels/servos, you need one line with source iRud, weight 50%
Under both inner Ail-channels another line with source iRud, weight opposite above -50%
During full R-Rudder you should see this