I was trying to diagnose a problem that I was having with my quad and I was trying to rule out er9x so I was trying to revert to factory firmware. Now I get this message when trying to flash the transmitter.
avrdude.exe: error: programm enable: target doesn't answer. 1
avrdude.exe: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
the transmitter is connected correctly and it is showing up in the device manager as per this screen shot. What can I do to save this? Thanks
d
Did I brick my transmitter?
Re: Did I brick my transmitter?
What programmer? You will need to check the connection between your programmer and the 9x.
-Gohst
Sent from my LG-P999 using Tapatalk 2
-Gohst
Sent from my LG-P999 using Tapatalk 2
Re: Did I brick my transmitter?
I have a smartyparts and everything looks solidly plugged in. If it is a connection why would it show up in the device manager?
D
D
Re: Did I brick my transmitter?
The programmer connects to the computer just fine. You can have the sp board by itself on the table and it will show in the device manager. The problem is between the sp board and the 9x main board.
-Gohst
Sent from my LG-P999 using Tapatalk 2
-Gohst
Sent from my LG-P999 using Tapatalk 2
Re: Did I brick my transmitter?
Clean the pads with some alcohol and make sure the pins are straight and making contact with the pads.
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Did I brick my transmitter?
Thanks to all who responded. I got it working again. I totally removed the smartieparts board, cleaned the contacts on both the 9x main board and the smartieparts board. I also replaced the screws that came with the board with hex head socket head screws that I could fully drive down without stripping the head. I think that the screws might have been the issue as I had a difficult time getting them in when I installed the board originally. I also replaced the USB plug with a custom cable that I fabricated as it appeared that the solder joints on the usb looked a little wonkie. Again thanks.
Re: Did I brick my transmitter?
Seems I remember reading about this before with Smarty ?roontoon wrote: I also replaced the USB plug with a custom cable that I fabricated as it appeared that the solder joints on the usb looked a little wonkie. Again thanks.
Re: Did I brick my transmitter?
Great that you got it working.. Well done
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW