Throttle cut
Throttle cut
Hi all
I have a turnigy 9xr using er9x firmware.
I am trying to get a mix that will be able to use my throttle stick to operate spoilerons without the motor also running,
Any help would be much appreciated.
Soco
I have a turnigy 9xr using er9x firmware.
I am trying to get a mix that will be able to use my throttle stick to operate spoilerons without the motor also running,
Any help would be much appreciated.
Soco
Re: Throttle cut
Add this mix to your throttle channel.
CHx -100% FULL switch ( the same switch you use for the spoileron mix)
When activate the switch for spoileron, the throttle will be held low by the mix above.
João
CHx -100% FULL switch ( the same switch you use for the spoileron mix)
When activate the switch for spoileron, the throttle will be held low by the mix above.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Hi Joao
Tried as you suggested but unfortunately the motor ran at full revs when spileron was switches on.
Soco
Tried as you suggested but unfortunately the motor ran at full revs when spileron was switches on.
Soco
Re: Throttle cut
Should be HALF, not FULL.
Re: Throttle cut
Kilrah, please read the Er9x manual, you can download it here:
viewtopic.php?f=5&t=6473
Why HALF, and not FULL? FULL should also pull the motor channel low
It works the same as a throttle cut..
Imagine you have the throttle on CH3
CH3 100% Thr
R -100% FULL
I know what happened and it was my mistake, sorry.. That's why we should always remove the prop when we work on electric models
I forgot to say it should be a REPLACE mix..
Make sure the multiplex is set to replace..
HALF and FULL should both work in this case
João
viewtopic.php?f=5&t=6473
Why HALF, and not FULL? FULL should also pull the motor channel low
It works the same as a throttle cut..
Imagine you have the throttle on CH3
CH3 100% Thr
R -100% FULL
I know what happened and it was my mistake, sorry.. That's why we should always remove the prop when we work on electric models
I forgot to say it should be a REPLACE mix..
Make sure the multiplex is set to replace..
HALF and FULL should both work in this case
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Hi Joao
my apologies, I had it at +100% rather than -100%. It now works.
Many thanks for your help
Soco
my apologies, I had it at +100% rather than -100%. It now works.
Many thanks for your help
Soco
Re: Throttle cut
Yeah, +100% also didn't help
Please make sure it is a replace mix, or it will be ADDING the value to the throttle channel instead of REPLACING, which is what you need.
João
Please make sure it is a replace mix, or it will be ADDING the value to the throttle channel instead of REPLACING, which is what you need.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Yes I did that part of the mix I did understand. There is still a small problem, the ailerons still operate until the stick goes past halfway, at that point they no longer operate. I assume its because the spoilerons (ailerons) are at their limit, is there a way of solving that?
Soco
Soco
Re: Throttle cut
Can you post your eepe or model file here?
You can right click on your model in eepe and save only the model settings. It's an .eepm file. Not necessary to post the complete eeprom. Then please post it here.
Like that we can see exactly what your model is doing and provide better help
João
You can right click on your model in eepe and save only the model settings. It's an .eepm file. Not necessary to post the complete eeprom. Then please post it here.
Like that we can see exactly what your model is doing and provide better help
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Never posted a file here, do I just cut and paste it or is there another way?
Re: Throttle cut
On the right side of the "Submit" button there is a button "Full editor". Click on it.
Then under the text box you can see a tab that say "Upload attachement", click on it, select the file and then click on "Add the File". Then click "submit"
If the model file is not accepted by the forum, please change it's extension to .txt for example, or zip it, and post the zip file here..
João
Then under the text box you can see a tab that say "Upload attachement", click on it, select the file and then click on "Add the File". Then click "submit"
If the model file is not accepted by the forum, please change it's extension to .txt for example, or zip it, and post the zip file here..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Question, are you trying to program differential on the ailerons?
I'm asking because you can do that going to "Edit mix" - Curve - and select Diff
João
I'm asking because you can do that going to "Edit mix" - Curve - and select Diff
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Also, at the moment , when the Thr stick is below the middle point, the ailerons will work as flaperons.. I guess you only want spoilerons?
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Joao
short answer is yes it is my intention to add some differential, the file I sent you has only been done on epee, therefore is very basic. I have seen in the mix that as you say differential can be added through curve. Maybe what I should do is flash the model from my transmitter so that you can see the full information, if that would help.
short answer is yes it is my intention to add some differential, the file I sent you has only been done on epee, therefore is very basic. I have seen in the mix that as you say differential can be added through curve. Maybe what I should do is flash the model from my transmitter so that you can see the full information, if that would help.
Re: Throttle cut
Yes I only want spoilerons, what I have done on my transmitter is to use some offset to counter the flaperons.
Hope I have explain that ok
Hope I have explain that ok
Re: Throttle cut
Here, I did a very basic setup. Of course if you pull both servos up, they will reach the limit and only move down. Otherwise you could even break them.. If you still want them to move both ways you will have to limit the amount of spoileron. But I think that also depends on the amount of aileron you have and the limits on that channel..
I added some Diff..
See what you think. The throttle only operates on the top half of the aileron movement.
Have a look at the manual I linked above. Read the Mixer-offset-fix offset chapter. Leave the fix offset box ticked. easier to calculate the offset..
João
I added some Diff..
See what you think. The throttle only operates on the top half of the aileron movement.
Have a look at the manual I linked above. Read the Mixer-offset-fix offset chapter. Leave the fix offset box ticked. easier to calculate the offset..
João
- Attachments
-
- ASW28-Test.eepm
- (1.43 KiB) Downloaded 395 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Throttle cut
Joao
With just a few very minor adjustments every thing is working perfectly.
I must give you my grateful thanks for your help and instruction.
Soco
With just a few very minor adjustments every thing is working perfectly.
I must give you my grateful thanks for your help and instruction.
Soco
Re: Throttle cut
Joao
Just one simple final question, where can I find the latest firmware update?
Soco
Just one simple final question, where can I find the latest firmware update?
Soco
Re: Throttle cut
Glad you got it working and that I've been of some help..
But it is important that you understand WHY it works
eepe should find the latest release version for you.. Or do you mean the latest test versions?
If so, please find them here:
viewtopic.php?f=5&t=4598
João
But it is important that you understand WHY it works
eepe should find the latest release version for you.. Or do you mean the latest test versions?
If so, please find them here:
viewtopic.php?f=5&t=4598
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW