Help Starting Off with eePe Software
Posted: Thu Dec 06, 2012 11:02 am
Hi,
First up - I apologise. I have tried searching for information, but maybe what I'm trying to achieve is basic it should be general basic knowledge - but I need some assistance getting me in the right direction please coz I can't seem to figure it out.
I've purchased a Tgy 9x. I was advised the original firmware wouldn't support what I was hoping to achieve, and have managed to get the Firmware upgraded to ER9x. It looks much nicer - although I still have no idea what I'm doing.
I've installed the eePe software onto my computer. (I used it for flashing, and I see that I can do all my programming via the computer, and simulate it first to make sure it's what I want - so I'm opting to program via my computer).
A few things I would like to achieve (at least to start off with) using the software, so I can simulate first:
1) I would like my ELE D/R switch to send -100% / + 100 % to channel 8.
I know - I'm sorry - it's simple, but I can't figure out what to do. I've gone to the Switches tab. The function dropdown confuses me. Sorry.
2) I would like my Throttle Cut switch to make the throttle -100% (for safety precaution).
3) If possible (and maybe this is asking too much), but I would like the following for Channel 6 (flaps):
When the Gear Switch is down, I would like Hov / Thr to be ignored, and flaps / Channel 6 to be controlled by the 3 pos switch.
When the Gear Switch is up, I would like the 3 pos switch to be ignored, and the flaps / Channel 6 to be controlled by Hov / Thr
I know I have no hope of figuring out #3, when I can't even do something as basic as #1.
I'm willing to go learn myself - I just can't seem to find the right link / search parameters to find out how to do all this programing on the eePe software.
Any assistance would be greatly appreciated!
Thanks in Advance...
Adz
First up - I apologise. I have tried searching for information, but maybe what I'm trying to achieve is basic it should be general basic knowledge - but I need some assistance getting me in the right direction please coz I can't seem to figure it out.
I've purchased a Tgy 9x. I was advised the original firmware wouldn't support what I was hoping to achieve, and have managed to get the Firmware upgraded to ER9x. It looks much nicer - although I still have no idea what I'm doing.
I've installed the eePe software onto my computer. (I used it for flashing, and I see that I can do all my programming via the computer, and simulate it first to make sure it's what I want - so I'm opting to program via my computer).
A few things I would like to achieve (at least to start off with) using the software, so I can simulate first:
1) I would like my ELE D/R switch to send -100% / + 100 % to channel 8.
I know - I'm sorry - it's simple, but I can't figure out what to do. I've gone to the Switches tab. The function dropdown confuses me. Sorry.
2) I would like my Throttle Cut switch to make the throttle -100% (for safety precaution).
3) If possible (and maybe this is asking too much), but I would like the following for Channel 6 (flaps):
When the Gear Switch is down, I would like Hov / Thr to be ignored, and flaps / Channel 6 to be controlled by the 3 pos switch.
When the Gear Switch is up, I would like the 3 pos switch to be ignored, and the flaps / Channel 6 to be controlled by Hov / Thr
I know I have no hope of figuring out #3, when I can't even do something as basic as #1.
I'm willing to go learn myself - I just can't seem to find the right link / search parameters to find out how to do all this programing on the eePe software.
Any assistance would be greatly appreciated!
Thanks in Advance...
Adz