Slow flaps (servo slow - delay)
-
- Posts: 14
- Joined: Tue Aug 14, 2012 2:47 pm
- Country: -
- Location: Toronto
- Contact:
Slow flaps (servo slow - delay)
How can I program servo slow on 3-position switch flaps? I have managed to program 3-pos flaps nicely (slaved to gear channel as advised on this forum), but I'd like them to expand slowly and not jumping around. If I just switch plugs, how then to assign new channel to throttle lever if ch3 is used for slow flaps?
Roman Bershadsky
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Slow flaps (servo slow - delay)
Have you tried the SLOW option in the mix?
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Slow flaps (servo slow - delay)
Stock firmware...
-
- Posts: 14
- Joined: Tue Aug 14, 2012 2:47 pm
- Country: -
- Location: Toronto
- Contact:
Re: Slow flaps (servo slow - delay)
I'm on stock firmware. Can't justify buying additional hardware to change firmwares. Stock should be good enough for me, even if I can't make slow flaps I'm a relative beginner, stepped up from basic 4ch non-programmable radio. This seems huge! So far I can see everything I need and much more even on stock firmware with exception of this servo slow feature.MikeB wrote:Have you tried the SLOW option in the mix?
Mike.
Roman Bershadsky
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
Re: Slow flaps (servo slow - delay)
Is $5 really too much? Even to go from a $50 radio to the equivalent of a $1000 radio?
-
- Posts: 14
- Joined: Tue Aug 14, 2012 2:47 pm
- Country: -
- Location: Toronto
- Contact:
Re: Slow flaps (servo slow - delay)
I'm a newcomer to this forum, but wiki here says that $45-$50 programming hardware is needed to do this, not including shipping. If I could get ability to flash firmware for $5 with shipping I would for sure consider it. Does it exist?Kilrah wrote:Is $5 really too much? Even to go from a $50 radio to the equivalent of a $1000 radio?
Roman Bershadsky
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
Re: Slow flaps (servo slow - delay)
The $45-50 (that actually went down to $35 now) are for the solderless smartieparts programmer. If you're ready to solder 6 wires in your radio (on easily accessible pads) then this is enough:
http://www.hobbyking.com/hobbyking/stor ... duct=21321
http://www.hobbyking.com/hobbyking/stor ... duct=21321
-
- Posts: 14
- Joined: Tue Aug 14, 2012 2:47 pm
- Country: -
- Location: Toronto
- Contact:
Re: Slow flaps (servo slow - delay)
Well, it's $5 plus probably $10 shipping and I have to solder to CPU legs... I don't want to mess with it just for slowing flaps, but I understand the appeal.
Roman Bershadsky
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
web designer, composer
http://www.romandesign.ca - award-winning Toronto Web Design Studio
My music: http://www.moebiuscat.com - Moebius Cat - listen and download free
Re: Slow flaps (servo slow - delay)
No legs, only pads for flashing. Legs are for telemetry.
And shipping, well, you'd just throw the thing in an order you do anyway
But I understand your point too
And shipping, well, you'd just throw the thing in an order you do anyway
But I understand your point too
Re: Slow flaps (servo slow - delay)
i gotta say. After having my 9x modded, i couldn't live without it. And now with telemetry and voice i couldn't use any other radio either even if the hardware is not the best quality. João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW