Page 1 of 1
Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 5:23 pm
by bivo
Dears,
I bought an used Taranis X9D Plus SE.
It looks to be working properly, however, I'd noticed the screens are mixing english with portuguese language.
Does anybody know how could I solve this problem?
Althought I'm Braziliam, I prefer english language.
The firmware version is: 2.3.9-otx
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 5:44 pm
by Kilrah
You can flash the English version of OpenTX.
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 5:53 pm
by bivo
How do I know which one is the English version?
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 6:51 pm
by Kilrah
You select your language and options within companion, then download the corresponding firmware.
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 7:28 pm
by bivo
Which driver is necessary to Windows 10?
I'v tried to install the zadig-2.5 but it doesnt have the STM device to be selected
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 8:27 pm
by bivo
Dears,
If I update the sdcard with the last version, is it possible to update the radio firmware throught the bootload function?
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 9:25 pm
by bivo
One more doubt.
I've tried to update the firmware by companion, however, when I select the write it, the message below is showed. Does anybody knows what could be?
"Could not check firmware from radio"
"Opening DFU Capable USB device... Can not open device"
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 10:34 pm
by Kilrah
Put the file in the firmware folder on the card and flash form bootloader.
Re: Mixed languages Taranis X9D Plus SE
Posted: Wed Jan 20, 2021 11:56 pm
by bivo
I did it, but it shows the message "Its not a valid file"
I'd copied the firmware "open TX 2.3.11" in the sdcard firmware directory.
The file is: opentx-x9d+-en.bin
Is there anything wrong?
The firmware installed is the 2.3.9
Re: Mixed languages Taranis X9D Plus SE
Posted: Thu Jan 21, 2021 1:01 am
by bivo
Solved!
I'd put the radio in the bootloader mode and so it communicated with companion and I updated the Kiradio firmware.
However, I found in the radio setup an option "USB Mode" that I set as "Storage" and know the radio communicates without being in the bootloader mode.
It was set as "Joystick" so i supposed it wasnt communicating for this reason.
Thank you very much for the Tips Kilrah
Re: Mixed languages Taranis X9D Plus SE
Posted: Thu Jan 21, 2021 8:41 am
by Kilrah
When USB mode is set as Storage you can read/write models and to the SD but not flash firmware (since the firmware is currently running), so flashing has to be done in bootloader mode.
Re: Mixed languages Taranis X9D Plus SE
Posted: Thu Jan 21, 2021 12:48 pm
by bivo
So, how must be set the USB Mode to update radio firmware using companion?
Re: Mixed languages Taranis X9D Plus SE
Posted: Thu Jan 21, 2021 4:19 pm
by bivo
I've noticed in my radio it doesnt matter how is set the USB mode, it just communicate with companion with the radio in the bootloader mode.
Re: Mixed languages Taranis X9D Plus SE
Posted: Thu Jan 21, 2021 8:34 pm
by Kilrah
bivo wrote: ↑Thu Jan 21, 2021 12:48 pm
So, how must be set the USB Mode to update radio firmware using companion?
It doesn't matter since you do that in bootloader mode.
Re: Mixed languages Taranis X9D Plus SE
Posted: Fri Jan 22, 2021 12:13 am
by bivo
Thanks Kilrah