X-Lite Pro
-
- Posts: 238
- Joined: Tue Dec 25, 2018 3:19 am
- Country: United States
X-Lite Pro
I know I keep asking these questions but...Is there a erskyTX version for the X-lite pro ?
Thanks
Allen
Thanks
Allen
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
Not at present as I only have a standard XLite, not the 'PRO. I do have the details of the differences, so I could attempt to port erskyTx provided someone else is prepared to test it. I currently have 25 transmitters as it is!
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
-
- Posts: 238
- Joined: Tue Dec 25, 2018 3:19 am
- Country: United States
Re: X-Lite Pro
So is the standard XLITE supported ? I like the small form of the controller when i fly my micro quads . But I only fly ERSKYTX . To me it's just better
Thanks mike
Allen
Thanks mike
Allen
-
- Posts: 238
- Joined: Tue Dec 25, 2018 3:19 am
- Country: United States
Re: X-Lite Pro
I know the Xlite is but is the Xlite S ?...I'm just trying to figure out which to buy and stay with erskyTX..I can buy the pro and test it for you but I know you have very little TIME to do this.
Thanks
Allen
Thanks
Allen
Re: X-Lite Pro
S and Pro are the same thing as far as firmware goes.
-
- Posts: 238
- Joined: Tue Dec 25, 2018 3:19 am
- Country: United States
Re: X-Lite Pro
Hi Mike,
I have a xlite pro that I can test with if you'd be willing to make the port and tell me what items are affected. Thanks.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
OK, I'll see what needs doing, give me a few days to investigate, I have the required information available.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Hi Mike,
Just checking to see if if you've been able to make any progress with the x-lite pro code. Thanks!
Just checking to see if if you've been able to make any progress with the x-lite pro code. Thanks!
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
I'll try to post something tomorrow.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
I've posted a test version for the XLite S/Pro, please test and report if it works.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Hi Mike,
I loaded it this morning and have a few questions/comments. When I first booted after install I got 2 messages.
Bad EEPROM data
Bad EEPROM formatting
Is this normal after the first boot? All subsequent boots have been good.
Here are the first things I've noticed:
1. The backlight doesn't seem to work at all. I've tried a number of different "Display" settings with no luck.
2. Calibration seems to show all controls working properly.
3. Haptic doesn't seem to be working.
4. Momentary switches don't seem to be recognized.
Are there other specific items associated with this model that I should be looking out for?
Thanks again for building this!
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
Yes to the EEPROM messages, I use a slightly different format of the EEPROM (also makes sure you can't run with openTx settings that would be meaningless).
I'll look into the backlight and haptic.
When you say momentary switches are these the hardware switches (buttons on the top?)? I may have them mapped to "PB1" and "PB2", look on the DIAGSWTCH menu for these.
Mike
I'll look into the backlight and haptic.
When you say momentary switches are these the hardware switches (buttons on the top?)? I may have them mapped to "PB1" and "PB2", look on the DIAGSWTCH menu for these.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Thanks Mike.
Yes, momentary buttons on top. They aren't listed on the DIAGSWTCH menu in any form that I can see and they don't register when I press them to set as a source. There doesn't appear to be a way to scroll on the DIAGSWTCH page, so I'm assuming that they'd be immediately viewable.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
I don't understand regarding the two buttons. I just flashed the test version to my XLite (non s/pro) and I see PB1 and PB2 showing in the DIAGSWTCH menu. What do you see in the VERSION menu?
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
I downloaded and installed X-Lite r222B3 from the test table. Pics of what I see are attached.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
You need to download from: https://openrcforums.com/forum/viewtopic.php?f=7&t=4676.
The file is: xliteS_rom.zip, dated 27-May-2021 23:10.
Mike
The file is: xliteS_rom.zip, dated 27-May-2021 23:10.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Got it thanks.
1. The backlight is now working, but the screen seems to be flickering like the refresh rate is low.
3. I believe I felt the haptic once, but am not sure how to set up a test for it. Any ideas?
4. Momentary switches are now recognized on the DiagSwtch screen, but I can't seem to use them as switches in the Mixer or Fl. Modes.
1. The backlight is now working, but the screen seems to be flickering like the refresh rate is low.
3. I believe I felt the haptic once, but am not sure how to set up a test for it. Any ideas?
4. Momentary switches are now recognized on the DiagSwtch screen, but I can't seem to use them as switches in the Mixer or Fl. Modes.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
Currently, PB1 and PB2 are not detected when editing a switch entry and pressing them (unlike other physical switches). You will need to step through the entries to find PB1 and PB2.
Go to the Display menu and set the brightness to 100. Does the screen still flicker? In the same menu, check the setting of the CONTRAST and see if that improves the display.
To test the haptic, go to the AudioHaptic menu, set the Haptic Strength to 5, Haptic Min Run of 20 is OK. Set a Global Voice Alert to use a switch of SA-, and set Haptic to Haptic1, then move switch A to the middle position.
Mike
Go to the Display menu and set the brightness to 100. Does the screen still flicker? In the same menu, check the setting of the CONTRAST and see if that improves the display.
To test the haptic, go to the AudioHaptic menu, set the Haptic Strength to 5, Haptic Min Run of 20 is OK. Set a Global Voice Alert to use a switch of SA-, and set Haptic to Haptic1, then move switch A to the middle position.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Okay.
I found the PB1 and PB2 buttons in the list now. Thanks.
100 fixed the flicker, and the contrast adjustment makes the screen good.
The haptic is not working with those settings. It seemed like it vibrated once during power-up initially maybe, but I can't be sure. It's definitely not vibrating with the switch.
This model is supposed to have a 6-axis sensor as well. Would that be displayed on the DiagAna page?
I found the PB1 and PB2 buttons in the list now. Thanks.
100 fixed the flicker, and the contrast adjustment makes the screen good.
The haptic is not working with those settings. It seemed like it vibrated once during power-up initially maybe, but I can't be sure. It's definitely not vibrating with the switch.
This model is supposed to have a 6-axis sensor as well. Would that be displayed on the DiagAna page?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
I've just posted a test version that should fix the haptic.
I haven't added the 6-axis sensor, I'm not sure for what it would be used. Without a Tx with such a sensor, it will be difficult for me to test its operation.
Mike
I haven't added the 6-axis sensor, I'm not sure for what it would be used. Without a Tx with such a sensor, it will be difficult for me to test its operation.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Thanks Mike. That did the trick for the haptic.
I currently don't have a use for the 6-axis sensor, but figured that it's installed, so having it working would be nice.
Can you point me in the direction of a 3-position switch triple rate how-to? I've just spent ~45min trying to set elev triple and cannot get it.
Edit: I got it after going through the dual rate portion of the manual several more times. Triple rates with a 3-position switch is really not intuitive to setup.
I currently don't have a use for the 6-axis sensor, but figured that it's installed, so having it working would be nice.
Can you point me in the direction of a 3-position switch triple rate how-to? I've just spent ~45min trying to set elev triple and cannot get it.
Edit: I got it after going through the dual rate portion of the manual several more times. Triple rates with a 3-position switch is really not intuitive to setup.
Re: X-Lite Pro
Hi,
Is there a way to get an Xlite-S version of the ErSkyTx ? At least a beta... All links seem to be gone...
I'm investigating a misbehaving stick on the radio and I'd like to see raw ADC values. I think OpenTX doesn't show these, and there was such an option in ErSkyTx (if I remember correctly)...
Is there a way to get an Xlite-S version of the ErSkyTx ? At least a beta... All links seem to be gone...
I'm investigating a misbehaving stick on the radio and I'd like to see raw ADC values. I think OpenTX doesn't show these, and there was such an option in ErSkyTx (if I remember correctly)...
Re: X-Lite Pro
Oh, my bad! Surely it's there!
Thanks a lot!
BTW, do you know whether X-Lite Pro supports both 5V and 3.3V Hall effect sensors on gimbals?
The radio on my desk has one gimbal with 3.3v sensors, and the other gimbal with 5v sensors. The one with 3.3v works fine, and the other one jumps between 0 and midpoint all the time, no matter what... Can't be calibrated... The [Anas] screen shows good values when gimbal is disconnected (I can short the signal pin to 0v or to 3.3v to get 100% / 0% readings), but starts jumping all over once gimbal is connected again... At the same time, my multimeter reports quite a nice ~0.5-4.5v sensor output, depending on the gimbal position.
P.S. This radio originally came with 5v sensors on both gimbals.
Thanks a lot!
BTW, do you know whether X-Lite Pro supports both 5V and 3.3V Hall effect sensors on gimbals?
The radio on my desk has one gimbal with 3.3v sensors, and the other gimbal with 5v sensors. The one with 3.3v works fine, and the other one jumps between 0 and midpoint all the time, no matter what... Can't be calibrated... The [Anas] screen shows good values when gimbal is disconnected (I can short the signal pin to 0v or to 3.3v to get 100% / 0% readings), but starts jumping all over once gimbal is connected again... At the same time, my multimeter reports quite a nice ~0.5-4.5v sensor output, depending on the gimbal position.
P.S. This radio originally came with 5v sensors on both gimbals.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: X-Lite Pro
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: X-Lite Pro
Hi Mike,MikeB wrote: ↑Fri Dec 23, 2022 3:59 pm On http://www.er9x.com/ there is a version of erskyTx for the X-LiteS (rev 223).
That link leads to a 'file not found' (and also for the regular X-Lite).
Re: X-Lite Pro
My memory is a bit hazy as to which models had what, but some FrSky radios came with gimbals that have hall sensors that put out PWM instead of being analog, sounds like it would be the problem there, you have PWM gimbals but the radio is expecting analog.andrewju wrote: ↑Fri Dec 23, 2022 3:56 pm The one with 3.3v works fine, and the other one jumps between 0 and midpoint all the time, no matter what... Can't be calibrated... The [Anas] screen shows good values when gimbal is disconnected (I can short the signal pin to 0v or to 3.3v to get 100% / 0% readings), but starts jumping all over once gimbal is connected again...
On models where that was a thing OpenTX would autodetect PWM gimbals at boot time and fall back to analog so if you connect PWM gimbals after powering on it won't work.
Re: X-Lite Pro
Ahhhh! So probably one can't mix PWM and analog gimbals on one radio (i.e. left stick analog, and right stick PWM)... And that must be the reason for the trouble I see...