Hi! How can I use the program to the programmer FTBB. Replaced on patched avrdude http://easyelectronics.ru/img/readydev/ ... g/FTBB.rar
But in setting the programmer FTBB pinb programmer and has not appeared.
FTBB on eePe
Re: FTBB on eePe
What's FTBB?
Z
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
Re: FTBB on eePe
Does the programmer list in eepe get updated by avrdude? or is it a list that is hard coded. I see a new programmer type for avrdude called FTBB. I think it might be using one of the FTDI chips directly as a programmer, but I'm not sure. I think his problem is that FTBB just doesn't show up in the list of programmers.
-Gohst
-Gohst
Re: FTBB on eePe
FT232R Synchronous BitBang - FTBB
2Gohst
Yes, it does not appear in the list of programmers
2Gohst
Yes, it does not appear in the list of programmers
Re: FTBB on eePe
I meant that question for Erazz. I don't know how eepe gets the list it does. I understand that your version of avrdude has the patch for this programmer.Dalt wrote: 2Gohst
Yes, it does not appear in the list of programmers
-Gohst
Re: FTBB on eePe
eePe reads the avrdude.conf file and extracts the programmers from there.
Couple o foptions:
1) avrdude file was not updated to include FTBB
2) the avrdude.conf file is malconfigured.
3) multiple copies of avrdude.conf - not reading the correct file:
For Linux: /etc/avrdude.conf
Windows: same folder as eepe.
Couple o foptions:
1) avrdude file was not updated to include FTBB
2) the avrdude.conf file is malconfigured.
3) multiple copies of avrdude.conf - not reading the correct file:
For Linux: /etc/avrdude.conf
Windows: same folder as eepe.
Z
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
Re: FTBB on eePe
The configuration file is the only one. list available on request I can see the programming. but the programmer list in eePe not updated even after restarting the program.
try to make it.
Code: Select all
#FTDI_Bitbang
programmer
id = "ftbb";
desc = "FT232R Synchronous BitBang";
type = ft245r;
miso = 3; # CTS(11 PIN FT232R)
sck = 5; # DSR(9 PIN FT232R)
mosi = 6; # DCD(10 PIN FT232R)
reset = 7; # RI (6 PIN FT232R)
;
Re: FTBB on eePe
I think I know what's going on.
remove all leading spaces in front of the work "programmer".
That should do the trick
remove all leading spaces in front of the work "programmer".
Code: Select all
#FTDI_Bitbang
programmer
id = "ftbb";
desc = "FT232R Synchronous BitBang";
type = ft245r;
miso = 3; # CTS(11 PIN FT232R)
sck = 5; # DSR(9 PIN FT232R)
mosi = 6; # DCD(10 PIN FT232R)
reset = 7; # RI (6 PIN FT232R)
;
Z
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
BEWARE - WE ARE IN THE AIR!!!
What goes up... Should be controlled by a 9X!
Re: FTBB on eePe
It did not help. List of programmers are not updated. The solution was found. The register which stores the settings of the program in line programming was written the name of the required programming. everything works. Thanks for the tips.