Nano QX
Re: Nano QX
Here's one I put together for my 9XR running er9x. It uses the 3 position switch to turn SAFE on and off, and the AIL switch for rates.
-
- Posts: 2
- Joined: Mon Sep 09, 2013 10:20 am
- Country: -
Re: Nano QX
Hello Joseph,
You can check my post here to program your 9xr to have 3 rates on the 3 positions switch.
http://forum.turnigy9xr.com/tri-rate-on ... -t718.html
Enjoy
You can check my post here to program your 9xr to have 3 rates on the 3 positions switch.
http://forum.turnigy9xr.com/tri-rate-on ... -t718.html
Enjoy
Re: Nano QX
The nano QX uses a momentary switch to select between safe and acro modes. So I put mine on the trainer switch.
-Gohst
-Gohst
-
- Posts: 2
- Joined: Mon Sep 09, 2013 10:20 am
- Country: -
Re: Nano QX
So do I gohsthb
-
- Posts: 11
- Joined: Fri Jul 26, 2013 8:23 pm
- Country: -
Re: Nano QX
Using this file on er9x with custom dsm2 module with radio from dx4e. Changed to protocol dsm/type dsm2only. Got it to bind, but will not respond to sticks. Copter comes on with full red led. Cannot change to SAFE mode with 3-pos switch.
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: Nano QX
Here my Nano QX file for 9X with DX4 DSM module.
trainer switch for safe mode
gear switch for dual rate
ele d/r for sticky throttle cut
trainer switch for safe mode
gear switch for dual rate
ele d/r for sticky throttle cut
- Attachments
-
- nano QX.eepm
- (1.23 KiB) Downloaded 601 times
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
-
- Posts: 11
- Joined: Fri Jul 26, 2013 8:23 pm
- Country: -
Re: Nano QX
Finally got my nano flying.
The previous file from josephizf, modified to DSM2:DSM2/DSMX + fixed Expo.
For some reason my expo for throttle was 35,70 so I was capping @ -70 for the low-end of the throttle curve. I changed it to -100/100 for the end points and sure enough I got a blue LED and throttle works!
I might try KAL's file for the heck of it too. I'll pull it up in eePe and check it out. I think I like the idea of the trainer for the safe more so than the 3-pos.
Next project may be to either put in a external port for programming my 9x or trying to stuff an arduino pro mini + bluetooth inside to use as a programmer. Right now I have to pull it apart every time I want to get at my programming header. Also, I still need to stuff my spektrum module into an actual module case as it's just exposed right now.
The previous file from josephizf, modified to DSM2:DSM2/DSMX + fixed Expo.
For some reason my expo for throttle was 35,70 so I was capping @ -70 for the low-end of the throttle curve. I changed it to -100/100 for the end points and sure enough I got a blue LED and throttle works!
I might try KAL's file for the heck of it too. I'll pull it up in eePe and check it out. I think I like the idea of the trainer for the safe more so than the 3-pos.
Next project may be to either put in a external port for programming my 9x or trying to stuff an arduino pro mini + bluetooth inside to use as a programmer. Right now I have to pull it apart every time I want to get at my programming header. Also, I still need to stuff my spektrum module into an actual module case as it's just exposed right now.
- KAL
- Posts: 552
- Joined: Thu Oct 10, 2013 4:36 pm
- Country: Germany
- Location: somewhere near Rothenburg ob der Tauber
Re: Nano QX
Before I put an USBASP inside the 9x I placed the 10pin-header in the battery compartment.
It still had enough room beside the lipo.
It still had enough room beside the lipo.
( TH9X / 9XTreme / FrSky DHT / Spektrum / Multi / RotEnc )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )
( 9XR PRO / erSKY9x / FrSky DHT / Spektrum / Multi / RotEnc / P3 as Slider )