PPM16 ?
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
PPM16 ?
Hey all,
More confusion.
I have the Trex 500 heli template (that I got from here) and in the eePe editor, under 'MIXES' Menu, the model template is using 16 Channels (Channel 11 being the highest of these 16 used).
If I go back to the first sub menu, 'SETUP' - 'Protocol' it is set for PPM
Should I leave that as is or change it to PPM16 for it to work properly ?
Totally befuddled by all this.
Any help appreciated.
Cheers,
BF:)
More confusion.
I have the Trex 500 heli template (that I got from here) and in the eePe editor, under 'MIXES' Menu, the model template is using 16 Channels (Channel 11 being the highest of these 16 used).
If I go back to the first sub menu, 'SETUP' - 'Protocol' it is set for PPM
Should I leave that as is or change it to PPM16 for it to work properly ?
Totally befuddled by all this.
Any help appreciated.
Cheers,
BF:)
Re: PPM16 ?
The channels above 8 in the template are "virtual channels", i.e. they are used only as temporary variables for the setup to work, they don't need to be transmitted to the model.
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Thanks for that.
I must be getting senile. having a real hard time getting my head around this Tx.
I can't even figure out how to assign a switch to say turn lights on & off. All this IF X = Y stuff is beyond me.
Can you help me with that too please ?
Cheers
I must be getting senile. having a real hard time getting my head around this Tx.
I can't even figure out how to assign a switch to say turn lights on & off. All this IF X = Y stuff is beyond me.
Can you help me with that too please ?
Cheers
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: PPM16 ?
Have you watched the videos yet?
Sent from my GT-I9300 using Tapatalk 2
Sent from my GT-I9300 using Tapatalk 2
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
Re: PPM16 ?
Need to know how your lights are supposed to be controlled. Is it a remote controlled switch conneted to a free channel of the receiver?BieneFlyer wrote: I can't even figure out how to assign a switch to say turn lights on & off. All this IF X = Y stuff is beyond me.
Re: PPM16 ?
Therefore I have modified my templates menu to offer a 'Switches' template that adds a 2 position and a 3 position switch.BieneFlyer wrote: I can't even figure out how to assign a switch to say turn lights on & off
So it's easy to check, how to setup a switch
Reinhard
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Kilrah wrote:Need to know how your lights are supposed to be controlled. Is it a remote controlled switch conneted to a free channel of the receiver?BieneFlyer wrote: I can't even figure out how to assign a switch to say turn lights on & off. All this IF X = Y stuff is beyond me.
Thanks kilrah,
Yes, I'd like to be able to turn a set of nav lights on and off from say channel 7 or 8 with the gear switch.
The lights plug directly into the Tgy (V2) 8 Channel Rx.
Re: PPM16 ?
Just add a 100% FULL Switch(GEA) on the channel in question.
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Thanks kilrah
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Ok,
I went into my Trex 500 template in eepe and opened the MIXES Menu
I edited the CH07 line to read; +100%FULL Switch (ELE)
Is that correct ? Seems to work ok in the simulate mode. By the way, I had to chose another switch as Rudder offset is assigned to the GEAR switch.
Am I correct in assuming if I chose for example (!ELE) the switch direction is reversed ???
Thnx
I went into my Trex 500 template in eepe and opened the MIXES Menu
I edited the CH07 line to read; +100%FULL Switch (ELE)
Is that correct ? Seems to work ok in the simulate mode. By the way, I had to chose another switch as Rudder offset is assigned to the GEAR switch.
Am I correct in assuming if I chose for example (!ELE) the switch direction is reversed ???
Thnx
Re: PPM16 ?
Exact
You could use -100% instead as well.
You could use -100% instead as well.
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Thanks for your patience Kilrah,
It's slowly starting to make sense.
Lot's of ways to achieve the same result too it would seem.
It's slowly starting to make sense.
Lot's of ways to achieve the same result too it would seem.
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
Oh,
And a big thanks to all who replied & helped me with this.
Appreciated !
And a big thanks to all who replied & helped me with this.
Appreciated !
Re: PPM16 ?
soon you'll be helping others
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 109
- Joined: Sat Feb 16, 2013 10:28 am
- Country: Australia
- Location: Sydney
Re: PPM16 ?
That would be great !jhsa wrote:soon you'll be helping others
Cheers & thanks again so much. I might be able to get my heli flying by the weekend after this.
Paul