Hi, I've made a model profile for a 4Ch Helicopter (V911) and I've noticed that when the heli goes forward its needs a bit more throttle 'cause the main rotor speed goes down a bit, I've red that its normal so to compensate the effect I've added a mix to the channel 3 (TRH), when I press the ELV Switch (The one I've choose for the mix) if i push the right stick to go forward the throttle gets an increment of 10, thats works ok but if I pull the right stick to move the heli backwards the throttle looses 10 Its there a way to get it working only when pushing the stick to fly forward?.
Thanks in advance.
Mix for 4ch Helicopter
Mix for 4ch Helicopter
Good winds and......happy Flight !
Re: Mix for 4ch Helicopter
What was the mix you used?
Add the curve |x| to the mixer that adds ELE to your THR
This means take the absolute value of x, and so only positive values will be sent to the mixer.
-Gohst
Add the curve |x| to the mixer that adds ELE to your THR
This means take the absolute value of x, and so only positive values will be sent to the mixer.
-Gohst
Re: Mix for 4ch Helicopter
Hi, this its my setup....
CH01
(+100%)Ail
* (+100%)CH06
CH02
(+100%)Ele
* (+100%)CH06
CH03
(+125%)Thr Switch(ID0) Curve(Curve 1)
(+10%)Ele Switch(ELE)
R (+125%)Thr Switch(!ID0) Curve(Curve 2)
R (-100%)MAX Switch(THR)
CH04
(+100%)Rud
* (+100%)CH05
CH05
R (+50%)P1 Offset (100%)
CH06
R (+50%)P3 Offset (100%)
Thx
CH01
(+100%)Ail
* (+100%)CH06
CH02
(+100%)Ele
* (+100%)CH06
CH03
(+125%)Thr Switch(ID0) Curve(Curve 1)
(+10%)Ele Switch(ELE)
R (+125%)Thr Switch(!ID0) Curve(Curve 2)
R (-100%)MAX Switch(THR)
CH04
(+100%)Rud
* (+100%)CH05
CH05
R (+50%)P1 Offset (100%)
CH06
R (+50%)P3 Offset (100%)
Thx
Good winds and......happy Flight !
Re: Mix for 4ch Helicopter
Did you notice that your 10% ele only gets added in mode ID0 ? If you wanted it to work in the other modes also, you need to move that mixer line down one. So it would be like this:
I have to ask (now that I noticed), which version of Er9x are you using? Max was changed to half a long time ago.
Also I would change your throttle from 125% to 100% and just use the curves to control the throttle channel output. With them set to 125%, channel 3 output gets to the highest point on the curve before your throttle stick moves as far as it can.
-Gohst
Code: Select all
CH03
(+125%)Thr Switch(ID0) Curve(C1)
R(+125%)Thr Switch(!ID0) Curve(C2)
(+10%)Ele Switch(ELE)
R(-100%)Max Switch(THR)
Also I would change your throttle from 125% to 100% and just use the curves to control the throttle channel output. With them set to 125%, channel 3 output gets to the highest point on the curve before your throttle stick moves as far as it can.
-Gohst
Re: Mix for 4ch Helicopter
Hi !
Thanks for the info, I don't noticed that the mix was only working for the ID0 mode Now I've changed it into the correct position
I'm on r788 , I'm gonna change the throttle from 125 to 100 also to get the full throttle at the end of the stick
Cheers
Thanks for the info, I don't noticed that the mix was only working for the ID0 mode Now I've changed it into the correct position
I'm on r788 , I'm gonna change the throttle from 125 to 100 also to get the full throttle at the end of the stick
Cheers
Good winds and......happy Flight !