Strange monitor display : RK Tx18S MPM radio

Help and support for any other brand radios
Post Reply
solentlife
Posts: 50
Joined: Fri Aug 05, 2016 6:25 pm
Country: -

Strange monitor display : RK Tx18S MPM radio

Post by solentlife »

Radioking TX18s
OTX 2.3.15 (latest)
MPM Module : 1.3.3.20 (latest)

No modifications or strange additions ....

Flys models well with no hint of problem ....

When setting up latest model ... 3D printed Sport Jet 50mm EDF ... I was using the Monitor function and noted that when moving Throttle stick (left Mode 2) ... the Elevator display showed interaction .... but model elevator was still ... no twitch nothing ...

Here's video :

https://youtu.be/ChoMkLTK8D8

Anyone else have this ????

solentlife
Posts: 50
Joined: Fri Aug 05, 2016 6:25 pm
Country: -

Re: Strange monitor display : RK Tx18S MPM radio

Post by solentlife »

Just to clarify .... all sticks / pots / sliders have been calibrated as well to be sure.

I have a new throttle gimbal on order due to my breaking the tension bracket ... repaired - but think this is opportunity to replace with the Jumper T16 Hall assembly - supposed to be a better gimbal ....
User avatar
Kilrah
Posts: 11108
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Strange monitor display : RK Tx18S MPM radio

Post by Kilrah »

Given the constistency it looks like you've explicitely got a mix set up to apply elevator compensation with throttle.
solentlife
Posts: 50
Joined: Fri Aug 05, 2016 6:25 pm
Country: -

Re: Strange monitor display : RK Tx18S MPM radio

Post by solentlife »

Update ...

Setting up more of the Sport Jet ....

Its a 4ch Rcvr with split ailerons / split elevator servos .... so to avoid having to rewire servo ... I have set :

Ch 1 = Ailerons via Y lead
Ch 2 = Elevator 1
Ch 3 = Throt
Ch 4 = Elevator 2 (reversed of course)

Interesting that when I tested .... I had servo movement on the model when moving throttle - something that I had not detected on other models. It was BOTH elevator servos moved Ch 2 + 4 .....

Now I am not happy .....
solentlife
Posts: 50
Joined: Fri Aug 05, 2016 6:25 pm
Country: -

Re: Strange monitor display : RK Tx18S MPM radio

Post by solentlife »

OK today ....

I've really been delving into my radio ....

Reset radio with clean SD card ... OTX 2.3.15 ..... no models / no scripts etc. Radio was already flashed with AETR FW correctly .. but re-installed

Installed EDGETX 2.8 .... clean

EdgeTX 2.8 with models etc from OTX SD card ..

Tried all sorts - in fact was afraid I was going to brick the radio ....

Conclusion :

1. It must be a hardware problem as it didn't matter what FW ... problem remained

2. Being used to OTX ... I found EDGETX annoying ....

I will wait arrival of my new Throttle gimbal ... install and see what happens. If no joy - then I may look at replacing with the RadioMaster vers2 ......

User avatar
Kilrah
Posts: 11108
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Strange monitor display : RK Tx18S MPM radio

Post by Kilrah »

Check hardware page / [ANAS], that's the raw stick input, if it moves unexpectedly there it's a hardware issue, if not it's the setup.
solentlife
Posts: 50
Joined: Fri Aug 05, 2016 6:25 pm
Country: -

Re: Strange monitor display : RK Tx18S MPM radio

Post by solentlife »

Yep did the Hardware page ... its a hardware issue ....... so :

Today I got 'p......... off' with it ...

Took back of radio ... took out both gimbals ..... magnifying glass inspected all .... couldn't see anything chafed or wrong ....

Took hint from a previous reply and swapped them over ... they won't fit in the mounts though as the tension parts are 180deg and hit the sliders ....
Switched on ... BINGO !! No errors at all .....

Put all back together ..... closed up .... switched on ... NO ERRORS at all .....

I noticed one thing .... doing calibration again ... ALL centres then zero ... which was not as before ...
Also letting go sticks - zeros were precise and no 'flypast' ....

NOW I'M HAPPY !!
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Strange monitor display : RK Tx18S MPM radio

Post by bob195558 »

Maybe try ERSKYTX (erskyTx for RK TX18S): http://www.er9x.com/
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
User avatar
Kilrah
Posts: 11108
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Strange monitor display : RK Tx18S MPM radio

Post by Kilrah »

bob195558 wrote: Thu Jan 05, 2023 2:57 pm Maybe try ERSKYTX (erskyTx for RK TX18S): http://www.er9x.com/
How is that going to help with what has been confirmed was a hardware problem, that's been solved now?
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Strange monitor display : RK Tx18S MPM radio

Post by bob195558 »

Sorry I missed that part, thank you for pointing it out, good job.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).

Post Reply

Return to “Other Radios”