3D printable case for GPS/Vario sensor
Moderator: rainer
3D printable case for GPS/Vario sensor
Hi All,
I could not find any printable cases for these sensors so I designed my own. Hope you like it !
https://www.thingiverse.com/thing:4561104
Regards,
Emanuel
I could not find any printable cases for these sensors so I designed my own. Hope you like it !
https://www.thingiverse.com/thing:4561104
Regards,
Emanuel
Last edited by Emanuel on Tue Aug 04, 2020 11:28 am, edited 1 time in total.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: 3D printable case for GPS/Vario sensor
Hi Emanuel,
The link does not work correctly or something ?
(404 YOU HAVE REACHED THE END OF THE THINGIVERSE).
Also maybe good to post it here "3D Printing": https://openrcforums.com/forum/viewforum.php?f=129
The link does not work correctly or something ?
(404 YOU HAVE REACHED THE END OF THE THINGIVERSE).
Also maybe good to post it here "3D Printing": https://openrcforums.com/forum/viewforum.php?f=129
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: 3D printable case for GPS/Vario sensor
Thanks for the heads up. I think its fixed now.
Re: 3D printable case for GPS/Vario sensor
Still broken
Re: 3D printable case for GPS/Vario sensor
Found the issue. I could only see this Thing myself as I did save it, but did not 'Publish' it correctly. Should be better now. Sorry!
Re: 3D printable case for GPS/Vario sensor
All good now...
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: 3D printable case for GPS/Vario sensor
Hi Emanuel,
Looks good, well done !
I use Simplify 3D slicer and I have been trying to separate the two parts without success.
I would like to try printing the top cover on it's side as I believe would then be able to print without supports.
Is there a way to separate the two halves in Simplify 3D
so I can flip the top cover on it's side ?
Looks good, well done !
I use Simplify 3D slicer and I have been trying to separate the two parts without success.
I would like to try printing the top cover on it's side as I believe would then be able to print without supports.
Is there a way to separate the two halves in Simplify 3D
so I can flip the top cover on it's side ?
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: 3D printable case for GPS/Vario sensor
I will put both separate files on Thingiverse. I prefer to print them like shown with some support underneath the top cover.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: 3D printable case for GPS/Vario sensor
Thank you !
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).