I'm trying to figure out how to get a micro brain flybarless gyro to run off of 1s. Currently, the micro brain used a Micro 5209 LDO regulator that requires +1v above output (3.3v out, so min 4.3vin). Here is the datasheet
The application uses 1s lipo which will drain to about 3.3v under load. No, I can't use 2s and weight is a major consideration.
I was thinking about a joule thief, but have never used one and wasn't sure if it would be suitable for such a sensitive electronic (gyro and frsky rx). I had thought about replacing the regulator with an even lower LDO, but have no idea how to find one (I tried using digikey but lack the knowledge necessary to parse through the inventory/search results)
What would you recommend?
The site won't let me attach the picture/file
Lower LDO Regulator on my gyro?
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Lower LDO Regulator on my gyro?
I don't know how much current your setup will drain but you might want to check the LP2981 (100mA max) and the LP2985 (150mA max).. They are very low dropout voltage..
You can't expect to discharge the LiPo battery until it reaches 3.3V with any regulator. Even the very low dropout regulators need some voltage at the input above the output voltage.
The dropout voltage also increases with the load..
João
You can't expect to discharge the LiPo battery until it reaches 3.3V with any regulator. Even the very low dropout regulators need some voltage at the input above the output voltage.
The dropout voltage also increases with the load..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Lower LDO Regulator on my gyro?
How about a tiny step-up to get the 5V back?
https://www.pololu.com/product/2564
https://www.pololu.com/product/2564
Re: Lower LDO Regulator on my gyro?
Kilrah, I think he needs 3.3V, not 5V?
Or do you mean, step-up converter to 5V and then an Low dropout regulator to get stable 3.3V?
João
Or do you mean, step-up converter to 5V and then an Low dropout regulator to get stable 3.3V?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Lower LDO Regulator on my gyro?
I mean step up to 5V so the device works as it's designed to without modifying it.
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Lower LDO Regulator on my gyro?
I was really hoping for a super ultra mega lower dropout regulator, but it looks like a stepup will have to be the solution.
Thanks, y'all!
Thanks, y'all!