Help with set up on a quad 250

[silversurfer48]

I have a 250 quad and has basic set up I read the manual and gone to some of the talks in in the forum but I still dont understand the set up on the CC3D and just dont know were to start

[bob195558]

Hi silversurfer48,
I have not used the CC3D flight controller.
But I do have some questions to help me better understand where you are having difficulty.

Are you asking help with setup of the CC3D flight controller ?

Or are you asking for help with your 9Xtreme radio setup for a Quad ?

Bob B.

[silversurfer48]

set up the conf. for 3D on the er9x tx I have basic settings
ch01 +100 % Ali
ch02 + 100% Ele
cho3 -100%Thr
ch04 100% Rud
ch05 R - 60%Full switch (L2)
R -100% Full Switch (L1)
R- 40% Full switch (L3)
R + 11% Full switch (L4)
R + 36% Full switch (L5)
R + 100% Full switch (L6)
ch06 + 100% P3
ch07 _100% Full switch (TRN)
ch08
ch09
ch10 + 100% CYC1
ch11
ch12
ch13
ch14 + 100% PPM2
But I have a problem with this set up on mixer the quad when turning to the left the right motors slow down and turn off and same for opposite side can someone HELP me with this and config. for 3D

[bob195558]

I think you have a 9Xtreme radio with erSky9x firmware on it and using eepSkye on your PC,
is this correct ?

I ask because you have written er9x which is a different radio firmware.

Bob B.

[silversurfer48]

Yes that's correct yeah I'm sorry about that I made a mistake but yes its ersky9x

[bob195558]

Hi silversurfer48,
I do not fully understand what all your mix settings are for.
I have not used mix settings like you have: CH14 + 100% PPM2
and:
CH05 R - 60%Full switch (L2)
R -100% Full Switch (L1)
R- 40% Full switch (L3)
R + 11% Full switch (L4)
R + 36% Full switch (L5)
R + 100% Full switch (L6)

But here is a basic model eeprom (zip file), which I use for my 250 Quad, which I use a
QQ flight Controller Board: (http://www.banggood.com/QQ-SUPER-Flight ... 10701.html) with it.
Make sure you do not use my 9Xtreme radio GENERAL SETTING as they are set for my 9Xtreme radio
which has several upgrade mods done to it.

9Xtreme 250quad 04062016.zip

9Xtreme 250quad April 06, 2016 eeprom

(1.01 KiB) Downloaded 272 times

If you view my 250 eeprom with your 250 eeprom with your PC eepSkye, I hope this will be a help for you.

Bob B.

[silversurfer48]

Ok does these settings also have for the CC3D mix

[bob195558]

OK does these settings also have for the CC3D mix

I have not used the CC3D FC board yet, but I have asked one of the members in our RC group,
who dose use and setup the CC3D FC board and asked if he could review your 9Xteme radio mixes.

I do use a MultiWii Flight Control board which I do use 9Xtreme switches to select MultiWii Flight Control board options, but because I have not used the CC3D, I do not know what it has to work with yet myself.

The QQ Flight Control board is very simple and very easy to fly with.

Bob B.

[silversurfer48]

I flashed your eepe rom,And made some minor changes and it seems to be doing ok I only wish I could get the rest of the quad set I'm talking about the cc3d I appreciate the help, Thanks dude

[bob195558]

I think you mean, used eepSkye to flash erSky9x-9XT to your 9Xtreme radio.
I am still waiting to here about making the setting for the CC3D FC board options.

Add more info: (https://www.youtube.com/watch?v=0hp01oVG-o0)
and (http://www.hobbyking.com/hobbyking/stor ... rized.html).
There seem to be several models of CC3D FC boards out there, so not sure what you have.

What are you using for a receiver ?

Bob B.

[bob195558]

Add more CC3D info here: (https://www.youtube.com/watch?v=ZK7Ikct ... tml5=False).

(http://www.geeetech.com/Documents/CC3D% ... 0board.pdf)

(http://www.headsuphobby.com/media/CC3D% ... .20.14.pdf)

(http://www.dronetrest.com/t/cc3d-flight ... -guide/830)

(http://www.banggood.com/OpenPilot-CC3D- ... 37044.html)

(http://www.buddyrc.com/cc3d-flight-control-board.html)

(https://www.youtube.com/watch?v=DRm_CyA ... tml5=False)

Bob B.

[bob195558]

Hi silversurfer48,
The members in our RC group who uses and setup CC3D Flight Control boards, said you should use the
basic model eeprom program that I posted earlier for your 9Xtreme radio 250 Quad model.
When you learn more about programming your 9Xtreme radio with erSky9x-9XT / eepSkye,
then you can make some changes to your eeprom program.

I think you maybe using a FrSky 4 channel receiver and so, next you will need
to setup you CC3D Flight Control boards and to (with) your 9Xtreme radio.
Search some youtube videos for some help with CC3D setup: (https://www.youtube.com/watch?v=e0hTYOv ... tml5=False).
(https://www.youtube.com/watch?v=Dk4xJNF ... tml5=False)

Bob B.

[silversurfer48]

Its all good , Thank you for your support that was pretty kool. This eeprom set up that you post I flashed on my TX is good for now. like you said its better for me to wait and learn myself, and make the change when I learn more about the ersky9x program, (Happy Flying Dude )

[silversurfer48]

receiver is a Turnigy 2.4 GHz 9X8Cv2 8ch full range receiver

[bob195558]

Hi silversurfer48,
I have a bunch of those Turnigy 8 Channel receivers and all of us in our RC Group will not use them
because they will fail at any time, breaking connection with your Turnigy transmitter (results Quad CRASH).
But if you get (use) the FlySky 6 Channel receiver (http://www.banggood.com/Wholesale-FS-R6 ... 68604.html) it is a lot better.

I suggest you take a look at the FrSky XJT module and get either the D-series or X-Series receivers as they are very reliable and you can add telemetry sensors, which once you start using telemetry, you will always then want to use it.
I mostly use the FrSky D-series 8 channel or X-Series 8 channel receivers with telemetry.
The FrSky XJT module works very will with your 9Xtreme radio and you will like it a lot.
You should also consider using a 5 volt / 5 amp BEC (UBEC or SBEC) to power your CC3D and Receiver in your 250 Quad.
I hope this helps.

Bob B.