Eachine ER transmitter

Help and support for any other brand radios
Post Reply
Saracen
Posts: 5
Joined: Mon Feb 10, 2020 3:38 pm
Country: United Kingdom

Eachine ER transmitter

Post by Saracen »

I picked up one of these on Facebook and wanted to have a play around with it.

It uses an ATMEGA128A, which I assume is what is usually referred to as the m128 processor.

It's running OpenTX 2.1.9, which I know is the last one to support AVR processors, so there's no upgrade path there.

My current issue is that I can't get it to talk to OpenTX Companion 2.1 on a PC.

When I plug in the USB lead, the EACHINE logo at the top of the transmitter lights up, so I'm getting power but the PC doesn't find a USB device.

I've found the correct buttons for the left and right trims but holding them down and powering on does not get into bootloader mode. Is that the correct procedure on this version of OpenTX ?

I know the lead and PC side is OK as I use the same ones to communicate with an X-Lite Pro with Companion 2.3

User avatar
Kilrah
Posts: 11108
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Eachine ER transmitter

Post by Kilrah »

What's that radio? Photo? Never heard of it.
There's no bootloader nor PC connection facility at all on AVR based radios, basically any exchange requires an atmega programmer. I doubt there's one built in to the radio.
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Eachine ER transmitter

Post by MikeB »

I wonder what the USB connects to in the Tx?

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
Saracen
Posts: 5
Joined: Mon Feb 10, 2020 3:38 pm
Country: United Kingdom

Re: Eachine ER transmitter

Post by Saracen »

Shipped as part of the package with their Novice III drone but never seen it advertised separately.

20200823_233053.jpg
20200823_233112.jpg

Two sticks, four 3 way switches (of which only one functions as a three way switch), two pots on the front.

Runs off a 3S lipo directly from the balance port (see below!)
Last edited by Saracen on Mon Aug 24, 2020 12:23 am, edited 2 times in total.
Saracen
Posts: 5
Joined: Mon Feb 10, 2020 3:38 pm
Country: United Kingdom

Re: Eachine ER transmitter

Post by Saracen »

> I wonder what the USB connects to in the Tx?

As it turns out, only two pins.

20200823_234841.jpg

The 8 pin chip on the right is a CS5095 USB to three cell Lipo boost charger chip.

https://www.programmersought.com/article/28633733031/

User avatar
Kilrah
Posts: 11108
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: Eachine ER transmitter

Post by Kilrah »

Saracen wrote: Sun Aug 23, 2020 10:55 pm As it turns out, only two pins.
Yeah that's what I expected, USB there just for charging.
Saracen
Posts: 5
Joined: Mon Feb 10, 2020 3:38 pm
Country: United Kingdom

Re: Eachine ER transmitter

Post by Saracen »

I thought last night I'd just put it back together again and sell it as a spare for someone. Then I remembered I had deleted the model, and have no way to reconstitute it. Rookie mistake!

So, what to do with it? As far as I can tell, it's effectively a Turnigy 9X in a different box.

Post Reply

Return to “Other Radios”