9XR Pro Screen not working on power up,

Cant get your radio to work? General Hardware issues?
Post Reply
User avatar
stotty1111
Posts: 233
Joined: Mon Aug 11, 2014 5:56 pm
Country: France
Location: overlooking Douarnenez Bay Finistere

9XR Pro Screen not working on power up,

Post by stotty1111 »

Hi all
Been a while, lost/misplaced my notes, I have a Pro tx, powering on, the blue power light works but screen remains 'dead' I remember a fix for this(dead resistor of 0ohms I think, just needing a bridge) but cannot find the piece, any suggestions please, and finally mr dumb here asking, a straight usb between the laptop and the tx?

ReSt
Posts: 1581
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: 9XR Pro Screen not working on power up,

Post by ReSt »

9XR Pro dead
============


I suspect that I have killed my radio when trying to check the voltages on the pins in the module bay. Maybe I inadvertently shorted something...

Now when I switch on, the screen remains blank

Measure R9 on the RF module board, inside the radio of course, not inside the RF module it should read around zero Ohms, just like a short.. R9 is a current sensor, and normally is the first to blow if you short something.
Might be this is what you where looking for??

Reinhard
User avatar
stotty1111
Posts: 233
Joined: Mon Aug 11, 2014 5:56 pm
Country: France
Location: overlooking Douarnenez Bay Finistere

Re: 9XR Pro Screen not working on power up,

Post by stotty1111 »

No , its not that, any other suggestions, later today I will clean all the plugs sockets and re make the screen connection etc
User avatar
stotty1111
Posts: 233
Joined: Mon Aug 11, 2014 5:56 pm
Country: France
Location: overlooking Douarnenez Bay Finistere

Re: 9XR Pro Screen not working on power up,

Post by stotty1111 »

Ok, cleaned/remade all connections in the tx, still nothing, only the power on blue light, also with the tx connected to my laptop, it is not detected, any suggestions please?
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9XR Pro Screen not working on power up,

Post by jhsa »

Please read Reinhard's post again. That is exactly what you want to do. I bet that R9 is broken.
And by the way, inserting or removing the RF module while the radio is ON might cause that R9 to fail.

João

EDIT: Or did I misunderstood your post and you did did measure R9? if so, what is the measured value?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
stotty1111
Posts: 233
Joined: Mon Aug 11, 2014 5:56 pm
Country: France
Location: overlooking Douarnenez Bay Finistere

Re: 9XR Pro Screen not working on power up,

Post by stotty1111 »

Yes, getting continuity across it with a reading of 0.7 ohms - a jumper wire perhaps?
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9XR Pro Screen not working on power up,

Post by jhsa »

Ok, then, do you have an RF module inserted? Does is control a servo?

if you turn the radio ON while pressing both horizontal trims to the center, and then connect to the PC, is it recognized by it?

If all this fails, please turn your radio ON and measure the voltage between both sides of R9 and ground. Be careful not to short anything.

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
stotty1111
Posts: 233
Joined: Mon Aug 11, 2014 5:56 pm
Country: France
Location: overlooking Douarnenez Bay Finistere

Re: 9XR Pro Screen not working on power up,

Post by stotty1111 »

So, set up an rf module and an rx with servos connected tried the bind procedure, it bound, switched all off, removed bind loop, switched on, tx then rx -no led showing in rx.no servo movement
Switch on pressing horiz bars, connect nothing
and the voltage check, with the rf board mounted or on its own?
Leaving the radio switched on there is a click every so often, cannot id origin, and the processor is very hot!
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9XR Pro Screen not working on power up,

Post by jhsa »

Oh, oh, processor very hot is not good :( Actually this is something I was going to ask you to check.
Either something is shorting one or more processor pins, or the processor itself is gone South, broken, kaput :(
Please disconnect everything from the mainboard except the LCD display and the connector that brings the power from the RF board. Remove also the RF module obviously.
Check if the processor still gets hot, and measure the output of the 3.3V regulator. As always, be careful not to short anything.

João
Diagram.JPG
(2.13 MiB) Not downloaded yet
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Post Reply

Return to “Hardware”