9XR Pro connection issues

[Anthonyc]

hi jhsa

i want to thankyou for helping me. tried another switch today and its working. i have a problem with the electromagnetics for the hopper door, i think i have a wrong mix and if you could help that would be great. These need to be only enegised when the left rud stick is held for 2 secs, at the moment they seem to get hot as soon as you plug in the battery and dont seem to energise on the command. The mix i have is +100%Rud delay(u1.5d1.5). I cant seem to figure how to get these to only energise when the rud stick is held left

Thanks

[jhsa]

do they need +100% to be energized?

If so, then on the channel of the hopper door try this.

CHx -100% FULL
-200% Rud Curve(x<0) Delay (u0:d2)

João

[Anthonyc]

Hi I can't seem to get - 200 on rud? Only - 125. I'm still quiet new to mixes so could be doing it wrong!

[jhsa]

That means you are running an old version of ErskyTX on yiur radio. Older versions could only do 125%
Another question, The rudder stick does only that or does it also something else?

João

[Anthonyc]

Hi

So been back to the original mix today of +100%Rud delay(u1.5d1.5). I reversed the polarity on the coil so black to red and red to black. Success the hopper dropped on the command. The only problem I have now is that it's keeping voltage going to the coil so once the door has dropped the coil is getting hot as it has constant voltage. Is there any way I can hold the rud stick left for 2 secs to de energise the coil and drop the hopper door then after 3 secs the voltage stops so the coil doesnt get hot and burn out? The only thing the rud stick is used for is hold left for 2 secs to drop the hopper door and hold right for 2 secs to drop the hook pin.

[jhsa]

perhaps it is possible using a "1-Shot" Logical switch.
Give me some time to try it in Eepskye. Can you send me the model so i can open it in Eepskye?

João

[Anthonyc]

Hi

Thanks that would be great if you could. How do i add the file? Its saying invalid file extension when i try to add it?

Thanks

[jhsa]

what file extension is that?
.eepe or .eepm should work. Or then just zip the file.

João

[Anthonyc]

baitboatnew27.01.20.eepe

(4.96 KiB) Downloaded 282 times

[jhsa]

Would you try this Please? It is difficult as I don't have the boat in front of me.

João

[Anthonyc]

Joao

You sir are a genious. That has cured the problem. Turns power off after 3 seconds and dropping the hopper door everytime. Is there anyway i can gift you some money as a thanks as you have really helped me out and i fully appreciate all you have done

Thanks again

[jhsa]

Great that it is working. Is all the blinking also working as it should? The problem (I think) was that after actuating the electromagnet, the channel was returning to 0 when it really needed to return to -100 so the switch would turn the power OFF.

I do like helping people using ErskyTX or Er9x, so no thanks. But if you insist, you could follow the link below my posts and donate to the Er9x/Ersky9x developer

João

[MikeB]

The USB connector on the 'PRO can be very stiff. When you plug the cable in, make sure you push very firmly, it "clicks" into place.

Mike

[Anthonyc]

Great that it is working. Is all the blinking also working as it should? The problem (I think) was that after actuating the electromagnet, the channel was returning to 0 when it really needed to return to -100 so the switch would turn the power OFF.

I do like helping people using ErskyTX or Er9x, so no thanks. But if you insist, you could follow the link below my posts and donate to the Er9x/Ersky9x developer

João

Hi Joao

So ive finally finished putting the boat together and im in the final testing stages, all is working as it should except the flashing lights on the back. Theres 2 light circuits, 2 white ones on the front on channel 3 and 2 blue on the back on channel 4. The blue lights on channel 4 should flash when the hopper and hook pin are activated, these do flash but only when the lights are in the off position on the ail switch. Could this be reversed easily? i did try but could not succeed in this

Thanks

[jhsa]

Can you please post your model again?
And should the blue lights flash when the Ail switch is ON?

João

[Anthonyc]

Can you please post your model again?
And should the blue lights flash when the Ail switch is ON?

João

Hey

Heres the model file.

BailBoat_1.eepe

(5.33 KiB) Downloaded 266 times

Yes please so when the Ail d/r switch is in the On position when the switch is down

Thankyou

[jhsa]

Hi, try this one I hope it works now

João