Turnigy 9x updated and now THR RUD and AIL switches are always on
Turnigy 9x updated and now THR RUD and AIL switches are always on
Hi all I tried to revive my old turnigy 9x with 64 Atmega but maybe I did something wrong 'cos now THR RUD AIL buttons doesnt' work anymore remaining in activate state.
I tried to flash 2.0 and 2.1 with and without frsky option without solving
now I am openttx-9x 2.1.10 eepr 216.0
The radio is modded with dht module and telemetry mod and it worked correctly before update If I remember correctly I had 1.9 before.
I tried flashing er9x (revision 821): but the switch error is still there
Any help?
Inviato dal mio Mi 9T utilizzando Tapatalk
I tried to flash 2.0 and 2.1 with and without frsky option without solving
now I am openttx-9x 2.1.10 eepr 216.0
The radio is modded with dht module and telemetry mod and it worked correctly before update If I remember correctly I had 1.9 before.
I tried flashing er9x (revision 821): but the switch error is still there
Any help?
Inviato dal mio Mi 9T utilizzando Tapatalk
Last edited by claustro on Tue Sep 08, 2020 7:01 am, edited 7 times in total.
-
- Posts: 277
- Joined: Sun May 06, 2012 8:37 pm
- Country: -
- Location: Fond du Lac, WI
Re: Turnigy 9x updated and switchs go mad
Did you attempt to re-calibrate the sticks and switches?
Re: Turnigy 9x updated and switchs go mad
Yes I calibrated without luck. I don't think there is an hardware problem because everything works fine before flashing.
It seems it doesn't recognize the frsky part of the firmware.
I don't remember but maybe I flashed a 2.2 version ( incompatible with this radio ) before downgrading to 2.1.10, could be this a hint?
It seems it doesn't recognize the frsky part of the firmware.
I don't remember but maybe I flashed a 2.2 version ( incompatible with this radio ) before downgrading to 2.1.10, could be this a hint?
Re: Turnigy 9x updated and switchs go mad
Solved the programming error changing usbasp I still have the switch problem
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9x updated and switchs go mad
"switch problem" Sounds like maybe Calibration is not correct yet.
Some times you need to try doing it several times.
Do you have the "Calibration" procedure ?
Some times you need to try doing it several times.
Do you have the "Calibration" procedure ?
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Turnigy 9x updated and switchs go mad
thank you for trying to help me.
If you mean the calibration procedure on the radio I have the option to calibrate pot ant stick. first on the centre and then on extreme positions. I don' know about a calibration procedure for the switches.
If you mean the calibration procedure on the radio I have the option to calibrate pot ant stick. first on the centre and then on extreme positions. I don' know about a calibration procedure for the switches.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
So, you only troubles with the pots ?
Are you saying you are trying to flash Opentx firmware and not er9x firmware ?
Better to stay with er9x as it is still supported: http://www.er9x.com/.
claustro wrote: ↑Mon Sep 07, 2020 5:42 pm Yes I calibrated without luck. I don't think there is an hardware problem because everything works fine before flashing.
It seems it doesn't recognize the frsky part of the firmware.
I don't remember but maybe I flashed a 2.2 version ( incompatible with this radio ) before downgrading to 2.1.10, could be this a hint?
Which Switches are now a problem for you and which firmware are you using ? http://www.er9x.com/
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
I flashed er9x last build and now the switches work correctly.I don-t know why open tx doesn-t work I use it on other radios so I-d prefear use the same firmware to all but no problem I-ll stick with er9c on the turnigy. Thank you very much for your help!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
Opentx is not supported anymore for a very long time now.
er9x is still supported and so is up to date and works a lot better then the very old Opentx for your 9x radio.
Glad you have your 9x working properly !
This may be helpful for you:
https://openrcforums.com/forum/viewtopic.php?f=5&t=6473
er9x is still supported and so is up to date and works a lot better then the very old Opentx for your 9x radio.
Glad you have your 9x working properly !
This may be helpful for you:
https://openrcforums.com/forum/viewtopic.php?f=5&t=6473
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
Thank you I downloaded the manual and for my needs this firmware seems perfect.
Thank you very very much for the help
Thank you very very much for the help
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
Er9x is a wonderful firmware. Abd it is still being maintained for this radio as far as I know.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Turnigy 9x updated and now THR RUD and AIL switches are always on
AI agree with you jhsa , using the firmare in the last 2 day I enjoie it a lor