Upgrade to V6 All Metal Hotend with V6 Heavy Duty Mount (CR10 3D Printer)
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Upgrade to V6 All Metal Hotend with V6 Heavy Duty Mount (CR10 3D Printer)
TH3D V6 All Metal Hotend with V6 Heavy Duty Mount Upgrade to the CR10 3D Printer
List of items I used:
1) V6 Tough Ultimate Hotend Package:
https://www.th3dstudio.com/product/th3d ... d-package/
or this https://www.th3dstudio.com/product/tough-v6-hotend/
a) Tough All-Metal Hotend w/Nozzles
b) Silicone Sock
c) Titanium Heatbreak
d) 50 Watt Heater
e) Thermistor
f ) Tough Tube - High Temp, Tight Tolerance PTFE Tubing with
Tough PTFE PC4-M10 Fitting
Tough PTFE PC4-M6 Fitting
https://www.th3dstudio.com/product/esse ... rade-pack/
g) 40mm 12V Fan
h) Two: 5015 12V Fans
2) CR-10/CR-10S V6 Heavy Duty Mount – 5015 Fan and EZABL (ABS):
https://www.th3dstudio.com/product/cr-1 ... and-ezabl/
3) Left-Hand 5015 Fan Add on Bracket (ABS):
https://www.th3dstudio.com/product/left ... n-bracket/
4) Two: M3 x 4mm Button Head hex-socket screws.
5) Two: M3 x 20mm Button Head hex-socket screws (5015 Fans).
6) Two: M3 x 10mm Flat Head hex-socket screws.
7) Two: M3 x 22mm Flat Head hex-socket screws.
8) Six: M3 Nuts. https://www.amazon.com/Shapenty-100PCS- ... -1-catcorr
9) Two: M3 x 12mm Allen Round-Head self-tapping screws (40mm Fan). 10) Three: JST-SH Servo Plug Wires (for making fan connections).
https://www.amazon.com/RCmall-Servo-Ext ... deo&sr=8-4 ----------------------------------------------------------------------------------------------
Process:
11) Note: I used for this upgrade, the Stock CR10 Extruder for this upgrade.
12) I also used the Stock CR10 Thermistor and Heater, which are
attached to the Hotend-Cable coming from the Control Box.
13) Remove the Stock CR10 Hotend-Cable from the Control-Box to the CR10 Printer. 14) Make the Fan-Wire ends and Hotend-Cable Fan-Wire ends to use the JST-SH Servo Plugs.
(Cut/Strip/Solder/Heat-Shrink-Tubing, to attach the JST Plugs) 15) At the bench, I fit these parts together before assembling them to the CR10 Printer.
16) After everything is attached and fitted together, I was then ready to assemble upgrade to my CR10 Printer.
.
..
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).