It is an electronic projects too, so it fits right here.
Very simple project that can be adapted to any 3d printer.
https://www.thingiverse.com/thing:3659699
DIY TOUCH-MI , wire-less autolevelling Z-probe(3D Printing)
DIY TOUCH-MI , wire-less autolevelling Z-probe(3D Printing)
Last edited by midelic on Fri Nov 15, 2019 4:58 pm, edited 1 time in total.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: DIY TOUCH-MI, wire-less autoleveling Z-probe (3D Printing)
Hi midelic,
We do now not have a category for "3D Printing" yet,
but hopefully we will some time soon !
I like to suggest that you mark at the end of the Tile Topic in parentheses,
something like (3D Printing), so that if/when there is a category for RC-3D-Printing
it will be helpful if/when a category for 3D Printing be made
and also would be a help when Searching for a Topics like this.
This project you have, looks very well done, good job.
Do you use a Raspberry Pi with EZPi image (Octoprint) ?
We do now not have a category for "3D Printing" yet,
but hopefully we will some time soon !
I like to suggest that you mark at the end of the Tile Topic in parentheses,
something like (3D Printing), so that if/when there is a category for RC-3D-Printing
it will be helpful if/when a category for 3D Printing be made
and also would be a help when Searching for a Topics like this.
This project you have, looks very well done, good job.
Do you use a Raspberry Pi with EZPi image (Octoprint) ?
Last edited by bob195558 on Wed Sep 16, 2020 1:25 pm, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: DIY TOUCH-MI , wire-less autolevelling Z-probe
Other Open Projects!!! There is now a "3D Printing" sub-Forum (with nothing in it!). I've just created it.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: DIY TOUCH-MI , wire-less autolevelling Z-probe
Hi Mike,
Thank you Mike for doing this !
The path to find where:
openrcforums.com / Board index / Other OPEN Projects / 3D Printing
https://openrcforums.com/forum/viewforum.php?f=129
Can the 3D Printing post here at "Other Electronic Projects",
the ones with (CR10 3D Printer) at the end of the Tile Topic,
be moved to this new category "3D Printing",
or would this mess-up the links to them ?
Thank you Mike for doing this !
The path to find where:
openrcforums.com / Board index / Other OPEN Projects / 3D Printing
https://openrcforums.com/forum/viewforum.php?f=129
Can the 3D Printing post here at "Other Electronic Projects",
the ones with (CR10 3D Printer) at the end of the Tile Topic,
be moved to this new category "3D Printing",
or would this mess-up the links to them ?
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: DIY TOUCH-MI, wire-less autoleveling Z-probe (3D Printing)
Done that(3D Printing).bob195558 wrote: ↑Wed Nov 13, 2019 4:14 pm Hi midelic,
We do not have a category for 3D Printing yet,
but hopefully we will some time soon !
I like to suggest that you mark at the end of the Tile Topic in parentheses,
something like (3D Printing)
Do you use a Raspberry Pi with EZPi image (Octoprint) ?
I don't have Raspberry Pi with EZPi image (Octoprint).
But as I'm a DIY guy I have ESP3D flashed on an ESP8266 attached to my 3Dprinter
https://github.com/luc-github/ESP3D
I plan to improve that DIY touch-Mi project adding on the back of it an ESP8266 and communicate with the existing ESP8266 connected to a z-probe connector.This way I can make it really wifi wireless.
I have made already the board and populate it I have still to pull myself out to do it.