9Xtreme Add 2nd Internal XJT Mod

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

bob195558 wrote: Sun Apr 30, 2017 9:26 pm
I think the 9XR is not able to do two transmitter module at the same time.
It depends if he is talking about the 9XR or the 9XR-PRO :) The PRO can do it, Not without some modding though.

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

no its the modul thats beeping its not the one in the radio or any of the beeping is not coming out from radio its diffently the XJT this is brand new modul and it was bind before the intial modification but after all the soldering and connecting to the 9xtreme board it started with the beeping and the receiver is no longer showing connected its not showing green light.but most diffently its the beeper on the modul where is the page were mike shows how to connect if this problem accures
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: RE: Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »


jhsa wrote: So, please post a link to the tutorial you followed to install the XJT module internally. We need to know how exactly the module is connected to the radio, and what was done to install it..



João

Sent from my thor using Tapatalk
Please answer my question above.

And please use some punctuation on your posts. I'm finding very difficult to understand them..

João


EDIT: Are you also saying that the receiver no longer binds to the XJT module?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

this is what i got
Attachments
the XJT in my 9x trying to make internal
the XJT in my 9x trying to make internal
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: RE: Re: RE: Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

jhsa wrote: Are you also saying that the receiver no longer binds to the XJT module?
Please answer?

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

Ok, on your picture, what is the green board below the XJT that you have the Telemetry (COM1) white and black wires connected to?

Also, what is the small board mounted vertically just below the 9xtreme board?

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

Please confirm you have the power to the XJT connected to Pin 7 of the expansion header. Please see picture attached..

João
Attachments
9-Haptic.jpg
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

yes
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

jhsa wrote: Mon May 01, 2017 9:18 am Ok, on your picture, what is the green board below the XJT that you have the Telemetry (COM1) white and black wires connected to?

Also, what is the small board mounted vertically just below the 9xtreme board?

João

Please answer the rest of my question above.
Please help us helping you.. You want help right??

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: RE: Re: RE: Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

jhsa wrote: Mon May 01, 2017 9:03 am
jhsa wrote: Are you also saying that the receiver no longer binds to the XJT module?
Please answer?

João
You also didn't answer this question.. I have to repeat my questions at least twice. Like this is impossible to help you. And we have also other stuff to think about, not only your problem. If you want some help please cooperate a little, otherwise as far as I am concerned i will have to leave it.. :(

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

black white wire connect to the DJT in the back of the receiver
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

yes it does not bind because its not working properly and aprt of that the modul is on it lights are on flashing and beeping
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

green board is the origenal board I put this in because of the extra connections your given when the smartie board is installed and less soldering
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

Ok, I don't like the fact that the module stopped responding :(
Did you check that the protocol for the internal module is correct?
Here is the link for the other thread where a similar problem is being discussed.

viewtopic.php?f=95&t=10109

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
silversurfer48
Posts: 88
Joined: Fri Feb 26, 2016 7:00 am
Country: United States
Location: Los Angelas Ca
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by silversurfer48 »

what is it suppose to be the black wire is not connected were would that go to and what are the settings in protcol
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by bob195558 »

silversurfer48 wrote: Mon May 01, 2017 12:47 pm black white wire connect to the DJT in the back of the receiver
Do you mean XJT module and not the DJT module ?
They are two different modules and have different Telemetry wiring connections.
XJT S.Port Telemetry black wire connection.
XJT S.Port Telemetry black wire connection.
Maybe you may want to try this XJT Module (back) in the external module bay to see
if it will work properly before you recheck all your internal module wiring connections.
Here is another place for more info about connections with the XJT Module: (viewtopic.php?f=126&t=7771).
What Receiver (RX) are you using (X8R) ? :?:

Bob B.
Last edited by bob195558 on Tue May 02, 2017 11:08 am, edited 2 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

Sorry I don't understand your post. :(

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by Hertz »

Great job guys!
Looking into converting my XJT for internal usage as well, I have a side-question which I couldn't answer myself by digging through the code.
How LUA/BASIC functions like `sportTelemetryPush` work? From what I see, XJT pin 5 is just a Tx, not half-duplex bidirectional for both Rx&Tx, and the code never configures `USART->CR3` register for half-duplex.
How are the values delivered from the Radio to the module, via the PPM/PXX/XJT pin?
As an additional question, do I need a one-way inverter for SPORT if I'm going to connect it to COM2 port on the 9Xtreme, or a two-way inverter like used for SPORT connection to F4 FCs?
P.S. Seems like SmartPort data is sent over the PXX/XJT line, now it makes sense :-)
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by MikeB »

The SPort signal is half-duplex, but the COM port is multiplexed outside of the processor using a 3-state buffer. The data polarity is inverted.

To use COM2 for SPort data you will need an inverter. There is no firmware support for sending SPort data out using COM2.
The 9Xtreme includes power switching for internal and external modules, so you will likely be able to use COM1 for both modules.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by bob195558 »

MikeB wrote: Mon Aug 21, 2017 1:03 pm The SPort signal is half-duplex, but the COM port is multiplexed outside of the processor using a 3-state buffer. The data polarity is inverted.

To use COM2 for SPort data you will need an inverter.
There is no firmware support for sending SPort data out using COM2.

The 9Xtreme includes power switching for internal and external modules,
so you will likely be able to use COM1 for both modules.
Mike.
Hi Mike,
When connecting Com1 telemetry to both internal and external XJT modules at the same time,
Hertz would have to (should) have only one of the modules turned on at a time ? :?:

If both internal and the external XJT modules were on at the same time,
would this cause a problem reading the telemetry on the 9Xtreme ? :?:

Other info: (viewtopic.php?f=126&t=7771&start=30#p105905)
bob195558 wrote: Fri Nov 20, 2015 1:07 pm XJT module Telemetry:
The radio decides whether the telemetry baudrate is 57600 or 9600 depending on the protocol, 57600 for PXX and 9600 for PPM.

When XJT module sends telemetry S.Port, 57600 baud using X-series receivers, connect the TX wire (Black) to Pin 5 or the
external S.Port Pin and radio setting are then set to Protocol: PXX and Sub-Protocol: D16 with both dip switches OFF (down).

When using telemetry baudrate 57600 for D-series receivers, connect the TX wire (Black) to 5 Pin or the external S.Port Pin
and the radio setting are set to Protocol: PXX (XJT name change) and Sub-Protocol: D8 with both dip switches OFF (down).

To have the TSSI signal reporting using D-series receivers: connect the telemetry TX wire (Black) to the external Txd Pin
and the telemetry RX wire (White) to the external Rxd Pin,
then set radio setting Protocol to PPM (baudrate 9600) and Sub-Protocol: D8
with the XJT module's dip switch 1: ON (up) and dip switch 2: OFF (down).
These dip switch settings changes the XJT module into a DJT module.
Bob B.
MikeB wrote: Sat Dec 12, 2015 11:32 pm I posted a new test version a bit earlier. Mainly it is to do with trying to fix a bluetooth problem,
but it does include a possible fix for your problem.
At the top of the telemetry menu is an option "UsrProto".
You should find an extra option at the end now of "FrHub".
If you select this, it is supposed to force the telemetry to process hub data at 9600 baud on your chosen "FrSky COM Port".
Mike.
I only needed telemetry from the external module and have my telemetry wires
through the back case, so that I can change the telemetry connection manually
to the external module.
The internal XJT module is set to PXX protocol with no telemetry wires to it.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by MikeB »

Either only one module on at a time, or, if using a XJT module in the external bay, disable telemetry operation on that module by setting both dip switches up and re-binding to a receiver.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

If it was me, I would go for the inverter on COM2, But that is me, of course :)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by MikeB »

But not if you need to send SPort data out on the internal module.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by jhsa »

Ahh, send data out.. Didn't know about that..
And not possible to make it work on COM2? Not that I need it of course.. :)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by Hertz »

Thanks guys, I would go for inverter to com2, was just curious whether it should be unidir or bidir like smartport.
But not if you need to send SPort data out on the internal module.
Hey Mike!
Do you intend that we can't send sport data out on the internal module?
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by MikeB »

The hardware was not designed to support TWO SPort connections. The FrSky transmitters have their internal XJT connected to the same SPort signal as any external module.

What configuration are you considering? If you connect the internal XJT SPort signal to COM1 (SPort connection), then all should work OK if you have any external module set to OFF (so not powered).

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by Hertz »

I plan on using XJT as an internal module with telemetry wired to either COM1 or COM2, and external module for Multiprotocol/EzUHF/Crossfire, but not at the same time. Hence I want telemetry from both internal and external, but only mutually exclusive.
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by bob195558 »

Hertz, you could purchase a Taranis-Plus and flash it with erSky9x and it can do SPort with com2.

Also another option with the 9Xtreme, you could just swap external modules,
or Mike suggestion, use com1 for both and turning off the module that is not being used.

Bob B.
Last edited by bob195558 on Tue Aug 22, 2017 12:59 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Hertz
Posts: 72
Joined: Wed Sep 30, 2015 2:14 pm
Country: -

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by Hertz »

Thanks, I don't need another radio, my Turnigy 9x is heavily modded already.
I just wanted to know how to wire it up properly, like Taranis does for instance, and if it connects both internal and external modules to the same UART I don't mind doing it that way.
As I said, I have no intention of powering both modules at once.
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9Xtreme Add 2nd Internal XJT Mod

Post by MikeB »

Yes, just connect both modules to the same signal (com1).
As an alternative, connect an internal XJT to COM1, and connect the external module to COM2 if it is only ever to be used for single direction data.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

Post Reply

Return to “9Xtreme upgrade board”