openrcforums

Yes conectir on the board, then any antenna with u.FL fits. It's not for the faint at heart to solder those u.FL to the board, but can be done. Next time I have mine open I'll take a picture if you need/want it.


Groot

Send from my iPhone using Tapatalk

and if you look at the tracks on the stock board (and you have the skilz or knows some one with them) you can stick in a u.FL on there. I have done that some time ago and it works fine. that is just a FYI.

Well I'm 1,75m and ....erm wait let's not go there, lets just leave it at my name fits ....

Yea I'll have to see, should run on the mac ...Have to find time to do it thou ....Erazz promised he will tell where he got the time he was looking for some weeks ago, but never did. Now I'm freshly out of time and don't seem to get more anywhere

Just got mine in the post ...Thanks SN and Rob for the combined effort. Now to find time for it ....argggg I have to use windowzzzz ???? have to look deeper into this ....

Groot

Also Note, on any solar system you want any measurement and controlling to use absolute minimum power. Those LED meter do eat a fair chunk of power. The meters listed above on ebay can be bought very cheap, if you search a bit on ebay. have Fun

michaelclyde wrote:welcome,
i was led to believe there would be snacks.

michael clyde

You can have the snacks ...Just LEAVE the BEER alone, it MINE

No need to panic ...Panic leads to damaged radio's ....Now lets start from scratch, Did you check the board for V1/V2 ?
Next did you clean the pads ...
Then please have a look here : viewtopic.php?f=11&t=19

some one will answer you with some clever way of doing it, but a hint I may give (instead of how to do it you can play and then remember how it is done for next time ...) CH5 - source P1 - weight 125 switch THR Max 125 Switch !THR (or -125 for the other side) CH6 - source P3 - weight 125 switch ELE ...

just to clarify, my understanding is board size is 45x45 outside, holes are spaced for smaller ...erm eraz can clarify that or maybe put up a dimension drawing ...also the size is universal and on a micro you do not need all those in/outs, that said it can be easy used on a micro quad/hex/octo and i...

I read until about this point .... Hello all, ..... Other options that are removed in favor of simplification are: 1) Limits - all limits are set to -125%..125%. This gives the full range of motion. Reduction in movement can be achieved through the Expo/DR menu . 2) The E xpo/DR menu was removed as ...

Thats the modules I was referring to. About the circuit I used, I have to dig for it and see.

Groot


Sent from my iPhone using Tapatalk

Most cheap dvm needs very low supply and current. IMHO you don't need a ubec. You can get units (display only) ready made for this. I will have a look for some links on ebay when I had some sleep, just back from nightshift. I made some circuits for the same purpose many years ago, it was self contai...

I'm from SA originally, but live in Germany.
I think you have been answered in the other thread. I was not sure if maybe the regulator got overloaded. if it does then you have the same type of symtoms, but seems it is not the problem in this case.

yes I have been looking at that one for some time ...and yes I will try and set all my channels to say 80% and test, but not today. this is for the weekend. Now I have officially hijacked this thread, so I should move it somewhere more appropriate very soon... but again not tonight, just back from l...

well TC use the same RX, and for him it works with a stock 9x (stock firmware) on the controller. He tested this and could not duplicate it. So now if some one has the same setup maybe they can test it with what ever flight controller or with a scope directly on the output. Think I have to find a ne...

Pxx in sure 16Ch ...erm now I need to spend more to add more to use all 16 :D how about replacing the compass you removed with a 2102 usb-uart ...make space for at least 2 mounting holes and if possible can you use standard 6pin header for isp ( I remember you said the pin layout was to save space),...

hahaha I also just spend more than I should have on buying small motors for a micro quad ...160mm motor to motor (defonzo frame)....I'll have to post a build log for it some where on this forum ... Now I think this Forum has grown from catering for 9x to full blown RC .... Personally I love the Naze...

As suggested elsewhere also, See if you can "tap" your 5v from the Buzzer/switch board, Not from the main board. You may be overloading your main board 5v regulator. That regulator is rated only 100ma ...and the one on the switch board is also 100ma but it's not used.

No! don't get the HK board ...it's only use is collecting dust. I have one and if any one wants it ....there is far better options out there. Pipo is one ....and seeing this is the Pipo thread I will not list the others, but be carefull on the controller, it will make or break your quad/multirotor ....

It's easy, can be done I less than 3 hours with basic stuff. Except for the flight controller a complete Quad can be done for less than $100 If you need to buy every thing. If you have some spare motors and ESC's then all you probably need to buy is a controller and some prop sets (cw/ccw) if you do...

perfect ...now this can stay for future showing how flexible the firmware is.

erm re-reading ....did you say standard firmware ..... .... am running the standard 9X FW...blablabla... then it's time to upgrade to er9x .... but still the answer is yes it will work [HiJack Thread] Why do I get problems when using 8CH in PPM sum on a D4FR once I have more than 6ch at Max ? On my ...

Cheers to taht

My suggestion is a 5v SBEC. Most Circuits nowadays use a 7805 from power source, so that is also a option. Personally I'll be using the 3s LiFe I have currently, with a 5v SBEC. They are fairly cheap and more efficient than the standard 7805. Most regulators can handel 12v input, and they do not rea...

Wish I could, but a tad far from me. It would be a nice birthday for me If I could have gone.

Yea, sorry, English is my Second Language ... and trying to post a fast reply while on the phone at work (in German, my 3rd Language) does not help either
Fixed it, and at least I had Windowzzzzz spelled corectly

The only thing you have to watch out for is radio setup like trim and endpoints. Changing RF modules types may require some small adjustments, but in theory it should all work. What I do know is when I changed firmware from stock to er9x I had to do complete setup from scratch for the Heli, but afte...

Ok lets see what I can answer for you : I have found the following TM-002 connector pinout: 1: PPM, 2: 6V DC, 3: Batt V+, 4: GND, 5: RF out - can anyone confirm this? Not sure but sounds correct According to TX9 schematics only GND and pin 3 (Batt V+) are connected to power supply. Is pin 2 (6V) pro...