openrcforums

It was down to me making a stupid mistake! - I set the source to a switch instead of MAX.

Once I changed the source to MAX I was able to set the end points and adjust the slider in the GUI.

I have a new Taranis Plus, with EU firmware and stock Taranis Opentx. I have successfully programmed my Tarot 680 Pro with Tarot ZYX-M FC and X8R receiver but am having problems with my DJI F450, Naza-M V2 and X4R-SB receiver. The receivers are both new, and have the 2015 EU firmware to match the TX...

Tarot gear - I have been attempting to adjust via the FC GUI, but it operates backwards i.e. if I move the slider into 'Down' position, gear goes up. If I invert the channel, the slider jumps to the 'UP' position and the gear goes down......

OK guys, this is probably the bone question of the week - I have an X9D Plus, brand new. I have programmed my Tarot 680 pro in fine, all works and flies as it should EXCEPT for the Tarot retracts. I have checked for any updates, and companion tx says the TX is up to date. I am using an X8R receiver ...

So simple -that got it!

Many thanks João

Might help if I put that it was ER9X that I have flashed it with......

Guys, I have just flashed a new Turnigy 9X which all went fine. This radio will be my spare, so I just copied my model profiles from my main radio (another Tgy 9X), now when I turn the set on I get the switch warning, but for ID0 - how do I change this so that it recognises ID0 as being the correct ...

I noticed that they had stock of the LCD, so bought the last one they had in stock (or I would have bought more) and now have a fully functioning spare Flysky TH9X Well chuffed!

OK, that's what I had, but could not understand why iy did not work - I re-bound the receiver, and all works as it should DOH!

The nav lights work direct as I am feeding them off a 5V UBEC, and using the signal pin to synch the lights strobe function (Flytron nav lights).

Many thanks (Y)

Jim

Gents, I have done a search but the results all seem to relate to the actual TX's control stick gimbals. I am trying to setup my TH9X with ER9X V1.394 to control my Tarot T2 gimbal pitch direct from a spare chanel on the receiver (not going via the flight controller), but am struggling. Loads of vid...

Do you still have the TX's? My LCD has packed up, so I am after a cheap new transmitter.

Jim

I'll nip round your place next time it needs doing then Mike........

Thanks for the info.

Success! - I guess the data transfer speed was too fast for the TX's chip?

Many many thanks guys! Now lets see if I can work this new system out.

Might be getting somewhere now, just did a read only with -B 100 and..... ================================================================================= Started AVRDUDE C:/Program Files (x86)/eePe/avrdude.exe -c usbasp -p m64 -B 100 -P usb -U flash:r:C:/Quadcopter/old.bin:r ======================...

Right, I uninstalled everything from windows and restarted the machine. I then reinstalled eepe and tried again, now it reads the data from the device, but then fails to write with the following error; ================================================================================= Started AVRDUDE ...

jhsa wrote:

Configure as C:/Windows/system32/avrdude.exe

Don't use this AVRdude.. Use the one inside eepe's installation folder.. See Mike's picture..

João

Changed it;
Made no difference

The TX is brand new, and has the later type board. Picture of wiring below as requested; http://i145.photobucket.com/albums/r216/Wreckymech/10365847_10205492146725565_106743119806536874_n_zpsbe3c60fd.jpg My adapter has a labelled fitting, so can't get the connection wrong; http://i145.photobucket.co...

Hi, Thanks for the response. I did not use any options when trying to flash. I have tried with the tx powered and through the programmer. eepe did nothing, which is why I tried companion - at least that showed me an error, eepe just sits on a blank screen saying reading from tx. I am going to have a...

I wonder if anyone can help me, before I lose it and smash my TX up! I have been trying all this week to program my Stock FS TH9X to my F450 Flamewheel, with no success. I decided to install ER9X to see if that would help, but alas, I have problems doing that. I am quite capable of soldering etc as ...