openrcforums

basic mcpx.eepe ID0 :- throttle up ID1 3d ID2 3d more throttle expo are different for each mode and expo is standard 20% on all modes. change to suit your own feel i find expo on throttle makes it less jumpy indoors and on calm day for hovering and general forward flight. this was programmed in Mod...

here is my MCPX template nice and simple 3 modes IDO is throttle up ID1 3d 40%expo ID2 3d 20% expo also a little higher throttle curve 20% expo on throttle seems to make it a little less jumpy when just cruising and hovering. throttle hold on THR switch HMMM how to attach the file ? i will add it to...

To add this was programmed in Mode 1

here is the full house, 7 servo glider eepe. this came from lesson 5 for all of us that didn't actually get that far in his modules. it has all the mixes AIL- RUD AIL -FLAP FLAP- ELE CAMBER/REFLEX CROW/BUTTERFLY THR HOLD THR SAFETY SWITCH MODE MASTER SWITCH( when in off position it is a basic plane ...

I did notice a lot of programs have !ID0 in them on ch6. I did 3 commands 1 for each position on the 3 point switch. What does the ! Mean before ID0.

I though something was weird but I understand now. I did just alter them around and gor the result I was afte getting servo moving in correct manner. Seems ok but still need to run through a few more option as I just did a basic program with 3point switch and 5 cures. 2 for pitch on ch6 and 3 forTHR...

oh forgot to mention i now also installed the HK UBEC and not taking power from 3.3v point of main board. it has full power now.

i hope someone can perhaps see where im going wrong as every time i download a eepm for mcpx CH1 show ELV Ch2 AIl CH 3 THR CH4 RUD. i have set general setting to be TAER mode 1, and in the preferences have done the same so when i import it uses these preferred channels for each thr ail elv rud swque...

Been away for a little while back back at it with a fresh look on it. It appears there was a busted wire on the plug. My fault may have knocked it installing dsm2 unit. Have it all working again binding to mcpx and orange r415 nicely. Have now got the switch working between the 2 protocol fuss and d...

Hi, i am trying to setup landing lights to turn on when the gear comes down.i have gear doors and gear on 2 seperate channels so i hab=ve the sequnece running but was thinking this may work. CH8 -100%FULL Switch(SW7) Cswitch7 v>ofs CH5 -100 i haven't tried this yet, I did try with CH* +100%Full Swit...

As i mentioned im a learner with this but now i have figures this oit. I did find my error. Is all good now and have the gear doors and gear sequence at a speed i like. Thanks again for the eepe file it has rally helped me also to learn the language.

same msg for when i turn on tx power it will not read or write with arvdude

another question can you confirm the trace i can cut to drop the power to the original module. is it in the same row as where the ppm signal comes from but not the top pin but the third down from the top of the tx.

it powered through the usbasp the screen is on showing flashing 4.7v i am powering module from the main board of the 3.3v ponit, its only a temp not intending to fly with this power option as of brown outs. it was meely to see if the module is working. i confirmed it is working with the orangerx r41...

here is the error msg if it helps avrdude.exe: warning: cannot set sck period. please check for usbasp firmware update. avrdude.exe: error: programm enable: target doesn't answer. 1 avrdude.exe: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check. av...

i have checked the path for arvdude alll is ok there, and i have the power light on the usbasp green light nice and bright. thinking i might desolder the dsm2 module toconfirm if this is the issue as nothing else is really different now i have reinstalled eepe and looked at the usbasp driver all goo...

As the title says, i am having trouble with eepe avrdude not working after dsm2 mod. it cam up with a few errors. i did download some files off 9x forum not able to remember who now but some put up some cpp files or something like that and some blade mcpx eepe settings.added them into my eepe file n...

was going to try bind to orangerx r415 but lipo went flat and funny thing is i realized i need to now make an adapter to fit my charger.grewat more soldering It works did a run up on the blade mcpx and it bound, power is still running of the main board until HK UBEC shows up, should be soon. Will pl...

Does anyone know the trace dayron was talking about to cut for inserting a switch to go between dsm and standard moduals. I understand how to wire it all up just not 100% on which trace to cut power to original module. My muly meter I thought I say two of these pins showing 5v. Going from some pictu...

Hi I hope you can help out. I have done the er9x mod and works well learning the programing is coming along but now I have pulled apart my dx4e got all the bit I need. I was thinking of salvaging the power switch from the dx4e I intend on leaving the original setup in as i have larger planes and hel...

thanks for the code Lennart, one thing i am trying to do is reduce the time delay on gear door closing and opening 6 seconds is a long time i would like it all to happen a little more closer. i have tried to reduce the delay to 2-3 seconds in place of the 6seconds delay on channel 8, the opening seq...