openrcforums

Out Standing!!

I assume the files are ready for the SD card as is?

Thanks for the reply
Bob
New Jersey USA

I'm having a heck of a time using the Open Tx Speaker. I see where the newly created file is saved on the left side of the screen, but it's nowhere to be found on my computer. Does anyone know how to get the file on the left side of the speaker program to save to the SD card? It is nowhere on my mac...

What is the process to save a file with the Open Tx Speaker?
I'm searching around for an answer, but thought I would ask here.

Thanks
Bob

Got it.

How would you go to a previous version if you wanted to?

Thanks
Bob

I'm thinking about updating one of my two Tarani to 2.08

Is there a reason the file is not listed here --> http://www.open-tx.org/downloads.html#Releases-ref
I understand to use Companion, but the site leads you to believe the file should be there.

Thanks
Bob

Thanks Scott
I don't want to be accused of hijacking the thread, and I mentioned that I'd start a separate one,
but isn't the intent to play the "modelname" AT startup?

Thank you.
I overlooked it.

Take care
Bob

On page 10 of this thread G550TED posted the instruction listed below. I'm hoping he's still around to help me with the set switch to "ONE" statement. I can't figure that out. Set a Custom Function and make it the first "Play Track" CF that you program. Set switch to "ONE&qu...

Thanks Buddy!
It was pretty ugly.

Attached is a screenshot of the message in case anyone else gets it...

Have a good one
Bob

Trying a practice post to see if the "Blacklist" syndrome is gone yet?

Thanks for the file. I had your link from a bit ago but work has been busy and I haven't had a chance to take a look at it yet. I need to get my priorities right d: To boot, I can't get on the board from home anymore. Something about being on a blacklist. I'll look at your file soon. I am very inter...

I thought it is 4 bit?

Another vote for program choices.
I've used Irfanview per instructions here, but my images are weak.

Thanks
Bob

I've been thinking about something.

What are the chances of using the right slider to adjust the amount of elevator compensation/weight needed in these mixes when the rudder is deflected?
Sort of an adjustment that can be done while I'm flying.

Attached is a basic model with the mix.

Thanks
Bob

I'll give that some thought.
So using "Replace" won't work?

I'm slowly understanding some of the logic of the system, but as expected it takes time.

What's more helpful to a Taranis user;
Math Skills
Programming Skills,
or just knowledge of the system?

Thanks again
Bob

I made the changes to my model and it works perfectly. I didn't mention that there are also three throttle curves in my set up, but that didn't make a difference. What is the rule on using an open channel for a mix versus putting the mix in the main line in the Mixer screen? Thank you again kind sir...

I currently use the JR 9503.
By "official adapter" I'm guessing I just plug the same adapter I use now to the back of the Taranis 1/8
phone jack slot, yes?

Thank you Mister Wizard!

Has anyone used the Taranis with Aerofly Pro Deluxe?

I'd like to know if it's possible, and what hardware is involved.

Thanks
Bob

I was on the road a couple of days.
Will try this out in a little bit here.

Thank you
Bob

I am used to using the left slider as my throttle trim on my JR 9503. I would like to add the LS as my throttle trim on the Taranis to act like the "IC Throttle Trim" option in the menu. I was able to add the slider but; (1) The slider doesn't kick in until after the slider is at center tr...

Thank you to everyone for the suggestions. GOHST Your mixes work great. I chose the non linear route to have some flexibility. I settled on Custom 9 point curves as they are convenient at 0 25 50 100 which makes it easier to estimate where to put the adjustments in the curves. The only down side to ...

Thanks Mike.
I understand that, but with the other system I use, it is not possible
to fly any other model with the same bound receiver, no matter what.

I know it's kind of unlikely to make that kind of mistake with this
system, but just to know it's possible is what I was after.

Take care

I did as you suggested and it works as advertised.
Thank You all.

There will be a time when maybe I can reduce the tremendous load on everyone here that helps out, and actually
be able to help out myself.

It's great work that you do, often with no appreciation or thanks.
Keep it up!

Hello I have a new X8R and I can select any model in my "Model Selection" menu and operate it with the same receiver by selecting that receiver in the "Model Setup" page. This would allow me to make a mistake by using the wrong model setup to fly the wrong plane if I'm not paying...

I think that is supposed to refer to if left rudder yields left aileron(bank) swap the weight to get right aileron(bank).

GHOST In your mix --> Rudder to aileron mix aileron channel +100% AIL +50% RUD other aileron channel +100% AIL -50% RUD It's been a long day and I'll have to try this in the morning, but with your mix, won't the ailerons go in the same direction (right bank for instance) with the application of left...

Thanks Ted.

It's on the To Do list...

Guys, I get the part about flying and mixing. I've been in the hobby since 1976, been to Iraq flying UAV's, and am still in the UAV industry. I'll reiterate and say that I am doing all of this on the bench. I have not flown the radio or put it in a model yet. I put some servos on a board and I'm wor...

jlunmel -->

I'll start another thread if necessary, but how would I play the name of the model at startup?


That would be just outstanding...

Thanks
Bob

Whew! So what is "SCup" and how do I learn about it/use it? I set up the aileron differential per a video by Scott? Can you school me on the "Differential" setting in the mixer? I needed a Knife Edge mixer and didn't know any other way to get the ailerons adjusted in a Knife Edge...