openrcforums

Hi, unfortunately it does not do the job.The 30 second timer runs fine from the SG switch but the 10 minuet timer does not start,would it be better if another physical switch was involved? As I've set this, the 10min timer starts when you put SG up after having put it down to start the motor and the...

Hi,

New wiki: DATA sent

Bye.

Hi,

You can try the eepe I've joined.

Bye.

The problem is the way |d|>=x is evaluated, it is reseted immediately after being true, so in this case after 1s. By increasing the delay in the logical switch, you can cope with slower LS movements at the expense of a longer delay in the voice announcement.

Bye.

Hi,

One possibility:
L1 will be on for 1s when LS makes CH10 changing, then,

the CH10 value is played once when LS is not moving.

Bye.

Hi,

It's not really electronics, just some easy soldering and Arduino basics: https://code.google.com/p/openxsensor/w ... uild_Vario

Don't be afraid to try

Bye.

Hi,

duncandan wrote:I am having trouble binding a V8R4-II receiver to my Taranis.

From the manual:

D_Mode (Telemetry)
Connect Ch1 & Ch2 signal pins of V8R4-II by provided jumper and then
connect battery to V8R4-II directly (no need to hold the F/S button on V8R4-II)

Bye.

Hi,

Roger wrote:... must now buy a couple of high precision varios.

Or you could make your own: https://code.google.com/p/openxsensor/

Bye.

Hi,

The correct wiring is detailed in the manual, you only need 3 cables:
- Yellow cable (TX port) from vario DATA out to the RX pin of the D8R-II
- V++ (red) and GND (black) to a RX servo connector

Then choose VSpd for the variometer source in the Taranis telemetry page.

Bye.

Thanks Tempo,

I've just added your link and another one I've found lately, it's in french but it is very well detailed:

https://code.google.com/p/openxsensor/w ... uild_Vario

Bye.

Thanks guys

Hi,

I've refreshed the "Building OXS vario" wiki: https://code.google.com/p/openxsensor/w ... uild_Vario

Bye.

Hi, I've only logged data with a Taranis and your file headers do not match mine: Your file: Time,Elapsed,Valid,RxRSSI,TxRSSI,A1,A2,AltB,AltG,Temp1,Temp2,RPM,Amps,Volts,mAH,TxBat,Vspd,RxV,Lat,Long,Fuel,SC1 Taranis working log: Date,Time,SWR,RSSI,A1,A2,A3,A4,GPS Date,GPS Time,Long,Lat,Course,GPS Spee...

New OXS Configurator v1.1 to download: https://code.google.com/p/openxsensor/wiki/OXS_Downloads I tried to set up an oxs as a voltagesensor without the vario features using the configurator. When triing to compile the sketch, i get the following errors... Fixed Found an new issue in oxs configurator...

Hi, I tried to set up an oxs as a voltagesensor without the vario features using the configurator. When triing to compile the sketch, i get the following errors: Thanks for the report, this error will be corrected quickly ;) I can confirm that. OXS configurator does not like voltage sensor only. Ple...

Hi,

michel49 wrote:I found the .csv datas files logged with my PRO can't be displayed with Companion 2.0.8

Put your file here so that we can test it.

Bye.

Hi,

This bug is already solved

https://github.com/opentx/opentx/issues/1584

Bye.

Hi SeaFrog, In my case, under XP SP3, once my Taranis was flashed with 2.x.x I found no reliable chance to handshake with it before removing the Zadig drivers. You know what, I'm also under xp and I've no problem at all ;) In fact, there is no relation between the different connection modes, it's li...

Hi, Instead, once the Taranis is flashed in 2.xx, it becomes a true standard storage device and the USB driver installed by Zadig must be DELETED : then the standard USB driver for Windows needs to be used and Windows will reinstall it once the Taranis is connected. Sorry but this is not true, you d...

Hi,

kalle123 wrote: but hopefully placed the right factor on the right position

Yes, this screen is right.



What you see in the right corner of the screen is the cells values, not ACCx.

And mstrens beat me to the answer...

Bye.

Best, I keep my mouth shut and wait for the documentation. What to do where ... No, no, you can ask what you want, your kind of questions can help to make documentation ;) About the dividers, those in the voltages tab affect the measurements directly and those in the Data sent tab affect the transm...

Hi,

kalle123 wrote: Badly waiting for a detailed instruction on https://code.google.com/p/openxsensor/wiki/

It will come, be patient

But 2.2 is not integer. So the rest of my questions still open.

I don't understand your remark as the divider factors have 2 decimals precision... Bye.

@Kalle123,

To understand better, how did you connect the voltages measured to OXS ? (schematics)

Thanks.

Hi,

New doc on the wiki: Vario settings

And the sidebar should work as expected !

Bye.

Hi,

AllanK1 wrote: Can I get a good template for 6 servo glider as a start point with flight modes. Where.

This is a pretty complete setup: http://www.rc-soar.com/opentx/setups/f3j/index.htm

Bye.

I've added some new doc in the wiki: https://code.google.com/p/openxsensor/wiki/OXS_Configuration The navigation side bar is not working very well for the moment... I reloaded OXS_Configurator_v1.0_linux.tar.gz just 5 min ago again from here https://code.google.com/p/openxsensor/wiki/OXS_Index I was...

Hi,

kalle123 wrote:Small issue with the gui ...
Could be location or rights on folder OXS_Configurator_v1.0_linux
br KH

I need more information to understand what the problem is:
- Did you download OpenXsensor v1.0 ?
- Where did you put openxsensor code ?
- What did you enter in the directory field ?

Bye.

Yes I agree, FlipFlop and Pulse would be really more explanatory.

Hi, I thought of all the people who are not firm with reading data sheets etc. ;) There's absolutely no way to DIY without reading data sheet so... e.g if the telemetry shows 200mA when there is no current (open circuit) I want to correct this 200mA. As Kilrah said above, the right way is to know th...