openrcforums

Hey Mike!

After a few hours of searching humans are going to be blind for obvious things. Your tip was absolutely the richt one!
Thank you very much!

And also Thanks to all of you guys that have been searching or thinking about what I have done wrong!

BR
Jörg

Good evening, I've got a problem with the er9x-Firmware. I was trying to build a trainer system with my old DX4e and my FS-TH9x with er9x-FRSKY(-NOHT) software mod. But when I activate the ability for trainer mode (Trainer ON/OFF) in the General Settings of my model I am loosing the stick control fo...

Hello guys! That trial was a fail! BUT I think I know why. rperkins@htpc ~/src/er9x-read-only/src $ diff -u pulses.cpp pulses.cpp.bak --- pulses.cpp.bak 2013-02-05 02:26:19.719678328 -0500 +++ pulses.cpp 2013-02-05 02:26:45.375678014 -0500 @@ -277,7 +277,7 @@ // /home/thus/txt/flieger/PPMtoDSM.c /* ...

I thank you very much! Do you know that your "+#define ...." will work the same way like a "#define DSM2_CHANNELS 8" ? So now my part of work will take a little bit more time. At first I have to implement the modul in my 9x. During that the parcel service has enough time to deliv...

OK, matches the previous answers then. The "good" module is usually too expensive to get, so it's not really used by modders, they use whatever it came with (DM9 for example) Sent via mobile I had a look at my "brandnew" DX4e that came together with my mCPx and in it is the AMTX...

Hey guys! I've got an answer! The supplier of information said: he just changed the value for #define DSM2_CHANNELS from 6 to 8. BUT the 8 channels are only available with an AMTX11-modul, with the X1TNX there is no way to get more than 6 channels. The posted part of code above (by rperkins posted) ...

The code below just pulled from er9x trunk shows that the serial dsm2 protocol used in the dx4e is limited to 6 channels. snippet of pulses.cpp // DSM2 protocol pulled from th9x - Thanks thus!!! //http://www.rclineforum.de/forum/board49-zubeh-r-elektronik-usw/fernsteuerungen-sender-und-emp/neuer-9-...

Hello cracks! I found that page! I'm sorry but it is a german speaking/writing. Our swiss guys shouldn't have problems to read it. Here's the Link . (Scroll a to the top, please) Once again sorry that i didn't found something in english. Maybe the guys with MX-16 are using a trick. They take the sig...

Sorry, but i think that isn't correct. The users of an MX-16 are including the modul from a DX4e in their Transmitters and can use 8 channels. I wouldn't pic up this idea if I wouldn't be convinced that there is a posibility I will lput in a link if I find once again. Thanks for your reply. BR Jörg

Hello to everyone! For the last days i was reading many many sites of stuff with the modding of the 9x to work with DSM2/X. I've got an burning question. Why is the 9x (er9x) just giving me 6 channels and not the full 8 channels? Is it possible to get the full 8? Is there any way? I'm very sorry, wh...

Ok! OK! Forget the question about the telemetry, It would be nice-to-have but when it is not able to get it isn't the end of the world. BUT: The Graupner MX-16 does support a 8 channel connection when the modul from a DX4e is built in. Why it doesn't work on our 9x? Can anyone explain it to me? The ...

Damn!
This is one channel too little.
Are the moduls in the DX7 and DX8 some other ones?

In fact, if I have too bye a DX7/8 to get more than 6 channels it is useless for me to implement the modul in my 9x.

Good morning, I've been reading a long time in here cause I'm using the 9x with ER9x firmware and here are all questions I had completly explained (thanks for that!), in exeption of two. I'm going to modify my 9x with a modul from the DX4e (DSMX) and I've got two questions about that. How many chann...