openrcforums

Hi Mike, Thank you very much for the explanation, I have made the configuration as you have mentioned, then I adjusted the multiplier a little so that the result was as indicated by the polymeter and finally I added an alarm in the Voice menu. I'm learning a lot, I had become outdated with Flysky re...

A clarification, when connecting the voltage divider if it marks RxV 10v, it marked zero because I had not connected the lipo. But I'm the same as yesterday, yes in A1 cha. I type 19.8 there is no data on the right and therefore no data and A1 appears. It is also tested in A2 with the same result.

Hi Mike, OK, I've already figured out the problem with the sound, it turns out that it sounds every 15s or so, it seemed like it only sounded once. On the turnigy128 the mix "warning" sounds every 2s. As for the voltage divider, I have tested what you say. When placing the jumper, the RxV ...

I tried in the audio menu what you were saying, I know why I listened to it at all, it only sounds once, this is configurable to keep playing, I don't see the way with the warning of the mix if I continue to play non-stop As for the voltage divider, that's where I stayed, I enter a value in A1, but ...

I'm looking for information on how to set up the voltage divider (FBVS) and connect it to the X6R receiver. From what I've read you have to remove the jumper from the AI2 port and plug AD2 right there, then configure A1, in my case for lipo 4S I'm putting 19.8v, but it doesn't indicate any kind of v...

How do you set up audible alerts for telemetry? Do you need the audio mod or is there some other way?

Hi Mike,

The option Warning in mixes, attached photos.

Hi Mike, I continued with the tests on the two teams 64 and 128. Testing sensors and setting alarms. In the 64 made missing in the mixes menu, the warning option to be able to configure the alarms. I've tried the er9xProv822z and er9xProv822z1 versions and I don't see this option. Could it be added ...

Hi Mike, Finally I solved it, I've gone a little crazy looking for the short, but in the end I saw it, with the datasheet of the turnigy 9x, it has also helped me to better understand the mod and finally find the error, I got the wrong pad, I soldered the resistance of the AIL on a pad that goes to ...

The Dual-Rate AIL should it work properly with the mod done?

Hi Mike, I've already tried the new version, it seems that the data is more consistent, although I don't see that moving the sensor up and down raises or lowers the height. I've tried giving the sensor a bit of heat, it raises the temperature and decreases the height..., Perhaps this is best tested ...

Thanks Mike for the explanation. Well, it looks like the temperature sensor is dialing correctly then. I'm waiting for your changes for the altitude calculation. You are a phenomenon, thank you so much for your help.

I discovered another one that I can't find in the manual that is at the end TmOK=2, this I don't know what it is...

A new fact that I didn't know, I just tested. T1=21. I understand you mean temperature??

Hi, Sure enough, it looks like a buffer and RAM memory problem, I installed the firmware ER9X-128PX5R822 and at least the sensor already marks as you mentioned. And as you mentioned, the values are not coherent, even if you raise the sensor the data goes down. Do you think that this inconsistency in...

Hi Mike, Load the latest firmware and it does the same as the previous ones, I attach a small video for you to see, you can see that the lighting flashes, lowers the battery voltage to 5v, as if the connector of the altimeter sensor tested a kind of short circuit... Sorry, the video turned upside do...

With both the Rate 50 and T-Rate 50, when the altimeter is plugged in, the illumination on the screen starts flashing and the telemetry is lost and the software is locked out. Tested with both test firmware er9x-128pz2r822.hex and er9x-128pz3r822.hex

And finally, removing the red wire, as you say, and leaving only the black one with the resistance, the equipment flashes and the telemetry works.

Well, and after all the problems and having managed to load er9x-128pz3r822.hex I did the test with the altimeter and the equipment started to flicker the light and stop working...., I turned it off and set the protocol as Rate 50 as you asked me to. The team stopped doing weird things, but the alti...

Finally, when the connector was removed, it was allowed to flap. I'm flying, I think I've tried this before.... And it didn't work.

I also tell you that in my case, if I don't connect this connector, the telemetry doesn't work.

Hi Mike, Disable the previous reading of the eeprom and continue with the same error. Then, following your advice with the polymeter, I tested continuity from the pads to the pins of the MOSI, RST, SCK, MISO, VCC and GND programmer connector,There seems to be continuity. I also tested the programmer...

pantallazos

The eepe messages, I noticed now that it seems to fail in a previous backup attempt?

As on this turnigy 128 I had xtreme, I removed the pcb, then I made the mod and finally upgraded from erskyTx to er9x-128pz3r822.hex

My 9xtreme has never worked well, That's why I've decided to make the telemetry mod and move on to Frsky.

Hi Mike,
attachment photos mod. In this Turnigy I had the 9xtreme installed.

Hi Mike, Remove the TX module and the same error. I tried removing the driver on windows and reinstalling it avrdude.exe: warning: cannot set sck period. please check for usbasp firmware update. avrdude.exe: error: programm enable: target doesn't answer. 1 avrdude.exe: initialization failed, rc=-1 D...

I've tried it but with the current firmware and the altimeter still doesn't work. I've tried upgrading to the test firmware er9x-128pz3r822.hex and I can't, I have the following error in eepe "avrdude.exe: warning: cannot set sck period. please check for usbasp firmware update." I can't re...

Hi Mike,

Flsyky 2A PWM-IBUS with receiver FS-IA6B and FS-IA10B.

Hi Mike,

Wonderful, it already works the same as in '64. With Flysky I had to change the option to 71 as well.
Although you can tell that the er9x goes smoother on the 128.
The Altitude sensor still doesn't work, I tried Alt and Galt, do you know if this works differently?

Hi Mike, I've already done the mod on the turnigy 128. I downloaded the firmware to the TX and performed the welds for telemetry just like on the turnigy 64. But there's no way for you to receive telemetry. I checked continuity with the polymeter in case there were any poorly made welds. I tried the...