Search found 33 matches
- Wed Sep 08, 2021 2:46 am
- Forum: Other Radios
- Topic: RM tx16s intermittent loss of control
- Replies: 0
- Views: 3321
RM tx16s intermittent loss of control
I need help with how to best troubleshoot an issue where my Tx is intermittently losing control of models. This has happened with by Frsky and Flysky receivers on at least 3 models. Fortunately for me, I didn't lose any models but I did crash a couple of times b/c of this. It's like it just decides ...
- Sun Feb 21, 2021 4:04 am
- Forum: openTx
- Topic: Transmitter power on delay - shut it off?
- Replies: 1
- Views: 2369
Transmitter power on delay - shut it off?
I cannot find a thread on this but When I had my Tarannis QX7, I had it programmed somehow to not delay when powering it on. Pretty sure it has to be done somehow in the source code but I can't for the life of me remember how. I want to do this for my Radiomaster Tx16s. It has a setting in the radio...
- Mon Feb 01, 2021 10:27 pm
- Forum: openTx
- Topic: Bugs 3 radiomaster tx16s not working at all!
- Replies: 0
- Views: 2063
Bugs 3 radiomaster tx16s not working at all!
See attached. anything I"m missing? Or is this a malfunctioning Bugs 3 board? It binds to my radiomaster. It just does nothing but solid led. Using the bugs protocol. Latest internal multi-module firmware. version 1.3.2.12 AETR
- Sat Jan 25, 2020 5:20 am
- Forum: FrSky Taranis radio
- Topic: telemetry voltage FrSky Smart Port Mini Lipo Voltage Sensor issue
- Replies: 2
- Views: 6337
telemetry voltage FrSky Smart Port Mini Lipo Voltage Sensor issue
I just got my Frsky S6R receiver setup with one of my planes and I have the FrSky Smart Port Mini Lipo Voltage Sensor plugged into the smart port, balance plug connected to the lipo. But when I try to discover sensors, all I get is RSSI and RxBat. This is supposed to read total and individual cell v...
- Sat Nov 30, 2019 4:40 pm
- Forum: General Information & Rules
- Topic: Can't find the iRange X main forum
- Replies: 1
- Views: 6225
Can't find the iRange X main forum
I want to post a question about the iRange X multiprotocol module but can't seem to find the main forum on this? Basically, I'm wondering how we go about requesting a new protocol to be added to firmware. (Omphobby M2 helicopter uses it's own protocol in the flight controller. Wondering if it's poss...
- Mon Oct 14, 2019 3:18 am
- Forum: openTx
- Topic: How do I add rudder to right stick in QX7?
- Replies: 1
- Views: 1933
Re: How do I add rudder to right stick in QX7?
Figured it out! All I had to do was set the ch 1 mix to a source of Ail and add a 2nd ch1 mix with source of rud. Viola, rudder control on both sticks.
- Mon Oct 14, 2019 2:46 am
- Forum: openTx
- Topic: How do I add rudder to right stick in QX7?
- Replies: 1
- Views: 1933
How do I add rudder to right stick in QX7?
Trying to add the ability to control the night vapor (indoor fly plane) steering rudder on right stick. It's a 3 channel plane so not sure if this can be done? Currently, I have the following setup which works as expected with elevator on the right stick, Rudder on the left and Throttle on the left....
- Sat Oct 12, 2019 3:28 pm
- Forum: The Pickled Gnu (The Pub)
- Topic: Help finding the power on delay for qx7 in source code
- Replies: 7
- Views: 15084
Re: Help finding the power on delay for qx7 in source code
oh, well I guess I will do that then. thanks. didn't realize I was not on the latest version.
- Sat Oct 12, 2019 12:49 am
- Forum: The Pickled Gnu (The Pub)
- Topic: Help finding the power on delay for qx7 in source code
- Replies: 7
- Views: 15084
Re: Help finding the power on delay for qx7 in source code
Hello, can someone please help me locate where I edit the power shutoff time? I'm using a QX7. Not finding any script files that would appear to have this in it. I have not yet messed with lua script as I'm new to open tx this year. (I know how to use the radio and all, but have not learned yet how ...
- Mon Sep 02, 2019 3:36 pm
- Forum: openTx for FrSky radios
- Topic: Turn LED lights on and off using a switch on QX7?
- Replies: 2
- Views: 3770
Re: Turn LED lights on and off using a switch on QX7?
Rats! I guess you get what you pay for.
- Mon Sep 02, 2019 5:21 am
- Forum: openTx for FrSky radios
- Topic: Turn LED lights on and off using a switch on QX7?
- Replies: 2
- Views: 3770
Turn LED lights on and off using a switch on QX7?
I have this LED light kit installed on my HK Tundra airplane: https://www.ebay.com/itm/Flash-LED-Light-Kit-for-RC-Helicopter-Aircraft-Airplane-8-LED-Lighting-System/202557257662?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D40719%26meid%3Dd364657e7f0e4dadae0fe17ac210a6f9%26pid%3D100675%2...
- Sat Aug 31, 2019 5:34 am
- Forum: openTx
- Topic: Throttle messed up on QX7 for one model
- Replies: 2
- Views: 2487
Re: Throttle messed up on QX7 for one model
Yep, I did end up pulling up the settings again and comparing to another when I did realize that one line was in there so I deleted it. All good now. one silly line is all it takes. lol
- Sat Aug 31, 2019 1:43 am
- Forum: openTx
- Topic: Throttle messed up on QX7 for one model
- Replies: 2
- Views: 2487
Throttle messed up on QX7 for one model
I'm pulling my hair out trying to decipher what my issue is. I just setup a new model for a Focke Wulf War bird. For some dumb reason beyond my comprehension, My throttle is not working unless I hold the timer reset button in and have it off throttle hold. I have attached the OTX file. The Tundra, t...
- Sun Aug 18, 2019 8:53 pm
- Forum: openTx model setup
- Topic: fmode setup not working so good
- Replies: 2
- Views: 6113
Re: fmode setup not working so good
Well, I got brave and decided to change the fmode gryo to to 30. Took it up and flipped into fmode 1 and it held! Yay! I didn't try any flips etc yet. want to make sure I got it perfect. Might lower it to 25 and keep going down a little at a time until it starts to tail wag then go up until it's per...
- Sun Aug 18, 2019 2:09 pm
- Forum: openTx model setup
- Topic: fmode setup not working so good
- Replies: 2
- Views: 6113
fmode setup not working so good
Greetings. I followed the steps in the following open tx university link for setting up my mixes and curves etc for my 470LP: http://open-txu.org/home/special-interests/helicopter/heli-part-2-mixers/ Only thing I did differently, is I put the fmode and gyro switches on the same switch. This way when...
- Sat Aug 03, 2019 10:14 pm
- Forum: openTx
- Topic: How do I read single cell voltages in Telemetry screen?
- Replies: 10
- Views: 8018
Re: How do I read single cell voltages in Telemetry screen?
I'm sensing some frustration on your part rdeanchurch. You need to realize this is all brand new to me. There is a forest of forums out there and it's very confusing to me and a challenge for me to know which forum to post what questions to. It's not about believing something you say. I am just igno...
- Sat Aug 03, 2019 6:25 pm
- Forum: openTx
- Topic: How do I read single cell voltages in Telemetry screen?
- Replies: 10
- Views: 8018
Re: How do I read single cell voltages in Telemetry screen?
I know how to setup the switches. The problem is I don't have any telemetry slot that reads cell voltage for a single cell. Just the total voltage. How do you add the single cell voltage option? Or is this dependent on the Rx? I"m using a lemon with telemetry which has a voltage sensor connecte...
- Sat Aug 03, 2019 4:10 pm
- Forum: openTx
- Topic: How do I read single cell voltages in Telemetry screen?
- Replies: 10
- Views: 8018
How do I read single cell voltages in Telemetry screen?
I want to setup a voltage alarm that tells me when a single cell goes below 3.6 volts. However, the telemetry screen in the QX7 only shows total voltage. Is there any way to setup the alarm to be based on a single cell going below 3.6 volts? I would assume you would need a sensor setup that reads si...
- Sat Aug 03, 2019 2:52 pm
- Forum: openTx
- Topic: No throttle using Irange X with a DSMX receiver
- Replies: 2
- Views: 2418
Re: No throttle using Irange X with a DSMX receiver
Nevermind. it's working now and now idea why. I plugged in a different lipo and the motor finally kicked on. so I put the other lipo back in and that works now too. no clue what that was about. sheesh!
- Sat Aug 03, 2019 4:54 am
- Forum: openTx
- Topic: No throttle using Irange X with a DSMX receiver
- Replies: 2
- Views: 2418
No throttle using Irange X with a DSMX receiver
pulling my hair out trying to decipher why I have no throttle on my plane. It's a standard setup with two ailerons. Everything but throttle is working. Here is what I have tried: 1. another receiver 2. another esc 3. another motor 4. all 3. On the motor mounted to the plane, it's completely dead, no...
- Fri Aug 02, 2019 3:03 pm
- Forum: General help (FrSky Taranis radio)
- Topic: QX7 copy just switches/functions etc instead of whole model?
- Replies: 3
- Views: 3124
Re: QX7 copy just switches/functions etc instead of whole model?
crud, that was the only thing I didn't try. lol. thanks!
- Fri Aug 02, 2019 2:45 am
- Forum: General help (FrSky Taranis radio)
- Topic: QX7 copy just switches/functions etc instead of whole model?
- Replies: 3
- Views: 3124
Re: QX7 copy just switches/functions etc instead of whole model?
So far, it appears you can copy/paste the mixes and inputs, but not the SF or LS stuff. If anyone knows of a way, please let me know.
- Fri Aug 02, 2019 1:13 am
- Forum: General help (FrSky Taranis radio)
- Topic: QX7 copy just switches/functions etc instead of whole model?
- Replies: 3
- Views: 3124
QX7 copy just switches/functions etc instead of whole model?
Is there any way to copy just for example the logical switches from one model to another instead of the whole model? For example, I will be using exactly the same logical switches for two planes. Would like to copy all LS from one to the other instead of having to do them all one by one manually. Is...
- Fri Aug 02, 2019 12:45 am
- Forum: openTx
- Topic: RSSI low and critical alarm fields in open tx companion doesn't go below 20
- Replies: 0
- Views: 2230
RSSI low and critical alarm fields in open tx companion doesn't go below 20
Per another forum related to the Irange X multi-protocol module with DSMX receivers, the consensus is you need to set the low and critical alarms to 18 and 15 respectively. So I did this on the radio then backed up the settings to companion. I noticed that they came over both as 20. This is a proble...
- Tue Jul 30, 2019 12:52 pm
- Forum: openTx
- Topic: Few questions/issues with QX7 configuring logical switches/telemetry
- Replies: 8
- Views: 6441
Few questions/issues with QX7 configuring logical switches/telemetry
Having the following issues trying to set logical switches for Telemetry voltage on the Taranis QX7, and RSSI: 1. I followed the steps in this link: https://oscarliang.com/setup-taranis-read-out-voltage/ But after adding the attached settings, I'm still getting the 0 voltage audio when turning on my...
- Mon Jul 29, 2019 3:54 am
- Forum: openTx
- Topic: First timer issues on QX7
- Replies: 16
- Views: 11778
Re: First timer issues on QX7
Now that I have one configured, it will be easy enough to just copy that one to use for my other DSMX models. Only got a few. I plan on buying some FrSky receivers going forward for any new models. It's working perfectly using the attached updated mix which I believe is what you were referring to an...
- Sun Jul 28, 2019 10:33 pm
- Forum: openTx
- Topic: First timer issues on QX7
- Replies: 16
- Views: 11778
Re: First timer issues on QX7
Ah, that makes sense. Thanks for the information. Good to know. I'm just ready to celebrate a victory of getting my first plane working correctly with the QX7 and the module. LOL. I think me and this new Tx are gonna get along just fine. I love the endless possibilities this setup brings, even if I ...
- Sun Jul 28, 2019 9:55 pm
- Forum: openTx
- Topic: First timer issues on QX7
- Replies: 16
- Views: 11778
Re: First timer issues on QX7
Bingo! I got my mix updated per the attached and it's working now! So basically in the mix, the first value should match the 'actual' channel order of the Rx which is TAER, but the 2nd part/column needs to show the order that the I-range apparently likes which is AETR. Very strange but Now I can jus...
- Sun Jul 28, 2019 8:33 pm
- Forum: openTx
- Topic: First timer issues on QX7
- Replies: 16
- Views: 11778
Re: First timer issues on QX7
So I tried the above and the throttle is now both on the left (correct) stick AND also still on the right stick from middle to high, but no elevator at all. So I'm closer but man this is confusing. Please let me know if I missed something in the above screenshot as that is the current mix I have. My...
- Sun Jul 28, 2019 8:13 pm
- Forum: openTx
- Topic: First timer issues on QX7
- Replies: 16
- Views: 11778
Re: First timer issues on QX7
see attached. is this what you mean?