Search found 192 matches
- Mon Nov 22, 2021 10:17 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: BEWARE OF FAKES !
- Replies: 1
- Views: 2446
Re: BEWARE OF FAKES !
Some Esc, peripherals like switch work only with old FM receivers with output signal of 4 volts pulse; all 2.4 give only 3 volts .
- Wed Sep 29, 2021 1:12 pm
- Forum: Turnigy 9XR PRO radio
- Topic: 9XR PRO - better gimbals
- Replies: 100
- Views: 156695
Re: 9XR PRO - better gimbals
Do you think it will fit inside the TH9X case ? it would be great assiocated with my AR9X board.
MP
MP
RPM set
How to set the number of blades in the RPM menu of AFHDS2a sensor ?
MP
MP
- Tue Aug 03, 2021 2:56 pm
- Forum: ersky9xr
- Topic: RPM sensor
- Replies: 8
- Views: 8715
Re: RPM sensor
Thanks kalle, very interresting; I suspect I have an issue with a 64mm EDF since I get only 19.000 rpm where it is claimed 3900 kv.
Is the Esc liable, is there a parameter to set.
The maiden flight - 800gr F22- was very slow, as expected...
Any idea .
MP
Is the Esc liable, is there a parameter to set.
The maiden flight - 800gr F22- was very slow, as expected...
Any idea .
MP
- Tue Jul 27, 2021 11:16 am
- Forum: ersky9xr
- Topic: RPM sensor
- Replies: 8
- Views: 8715
Re: RPM sensor
OK Mike, I dismanteld an old BL motor and count the number of coils, when I get 12 coils the pole number will be 6 or 12 ?
MP
MP
- Sun Jul 25, 2021 3:39 pm
- Forum: ersky9xr
- Topic: RPM sensor
- Replies: 8
- Views: 8715
Re: RPM sensor
How many poles have you set on the sensor? That's the question ! I believe the true RPM is given by my old Jeti Box associated with the MRPM sensor and, when set to 10 poles, I get around 24000 RPM I checked the FrSky sensor equally with a Tx running OTX which give the same 20-25% reading when the s...
- Sat Jul 17, 2021 6:38 pm
- Forum: ersky9xr
- Topic: RPM sensor
- Replies: 8
- Views: 8715
Re: RPM sensor
It is the FrSky S-Port RPM sensor where I set the poles number with 4 leds and the FW of the Tx is ErSky9xr where there is nothing to set.
- Sat Jul 17, 2021 9:33 am
- Forum: ersky9xr
- Topic: RPM sensor
- Replies: 8
- Views: 8715
RPM sensor
Hi,
I use the RPM sensor to get the RPM of my EDF and, once set the poles number I get a reading not true, around 20% of the real RPM when checked with an other system.
Where is the issue ? HW or software ?
MP
I use the RPM sensor to get the RPM of my EDF and, once set the poles number I get a reading not true, around 20% of the real RPM when checked with an other system.
Where is the issue ? HW or software ?
MP
- Wed Jul 07, 2021 3:24 pm
- Forum: Turnigy 9XR PRO radio
- Topic: Flashing Frsky receiver firmware via 9XR Pro
- Replies: 10
- Views: 9844
Re: Flashing Frsky receiver firmware via 9XR Pro
Thnks Mike, in order to avoid a mistake: you tell I use the lower of the five pin connector of the JR box is linked to the SPort pin and I power the Rx with my own 5 volts pack ?
- Wed Jul 07, 2021 8:21 am
- Forum: Turnigy 9XR PRO radio
- Topic: Flashing Frsky receiver firmware via 9XR Pro
- Replies: 10
- Views: 9844
Re: Flashing Frsky receiver firmware via 9XR Pro
Can I flash a Rx with a PRO and multimodule ? and how to link the Rx Sport ?
MP
MP
- Fri Apr 02, 2021 8:59 am
- Forum: ersky9xr
- Topic: delta expo
- Replies: 4
- Views: 5546
Re: delta expo
Thanks Mike,
The arm of one servo was not at neutral, now I set the neutral with Ele shift and AFTER I set the Ail+Expo and now the travel is OK.
My mistake was to set first the arm neutral with Ail shift
MP
The arm of one servo was not at neutral, now I set the neutral with Ele shift and AFTER I set the Ail+Expo and now the travel is OK.
My mistake was to set first the arm neutral with Ail shift
MP
- Thu Apr 01, 2021 12:22 pm
- Forum: ersky9xr
- Topic: delta expo
- Replies: 4
- Views: 5546
Re: delta expo
I have the same amount on the two AIL , you can see on the simulation:
CH02 +35%Ail Decalage(-35%) Expo (40)
+54%Ele
CH03 -54%Ele
+35%Ail Decalage(-15%) Expo(40)
MP
CH02 +35%Ail Decalage(-35%) Expo (40)
+54%Ele
CH03 -54%Ele
+35%Ail Decalage(-15%) Expo(40)
MP
- Thu Apr 01, 2021 9:03 am
- Forum: ersky9xr
- Topic: delta expo
- Replies: 4
- Views: 5546
delta expo
I have an issue when I set the expo with my PRO in delta config
I don't get the same servo displacement on both sides of the AIL , I suspect the different shift between CH 2 and 3
MP
I don't get the same servo displacement on both sides of the AIL , I suspect the different shift between CH 2 and 3
MP
- Sun Mar 21, 2021 12:27 pm
- Forum: ersky9xr
- Topic: remote with blutooth
- Replies: 0
- Views: 4067
remote with blutooth
I guess there is a way to use bluetooth to make a link between two Tx in order to get a master slave protocol; is it possible to use the same bluetooth link with a PC to get the remote control of a simu ?
MP
MP
- Sun Mar 14, 2021 3:26 pm
- Forum: Software
- Topic: 9XR PRO Bricked problem
- Replies: 16
- Views: 10122
Re: 9XR PRO Bricked problem
R9 is used to measure (Amp meter) the drain of the Tx in order to check the charge level, not necessary, you can short it...
- Thu Dec 17, 2020 4:53 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 4
- Views: 4322
Re: X8R burned regulator
Nope, issue fixed !
- Wed Dec 16, 2020 8:52 am
- Forum: ersky9xr
- Topic: AFHDS-2A telemetry
- Replies: 2
- Views: 4874
Re: AFHDS-2A telemetry
Thanks Mike, I 'll try that
MP
MP
- Tue Dec 15, 2020 3:59 pm
- Forum: ersky9xr
- Topic: AFHDS-2A telemetry
- Replies: 2
- Views: 4874
AFHDS-2A telemetry
I use the TH9X/AR9X with the last FW 223 and the STM32 multi-module with the last FW. I get RSSI and volt sensor but not the alt sensor; in the telemetry menu I selected the AFHDS2 option; is there a parameter wrong ? I get the alt sensor with Opentx and this module; I guess there is a bad parameter...
- Thu Dec 10, 2020 12:27 pm
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 4539
Re: Jeti Duplex telemetry
OK Kilrah, a good challenge, isn't ?
- Wed Dec 09, 2020 10:07 am
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 4539
Re: Jeti Duplex telemetry
I'm not sure to understand the goal of the electronics described; I hoped a simpler way where the data wire of the Jeti module was linked to pin 5 of the JR bay like the 4in1 module do and OTX translate the telemetry datas stream in the same way as Spektrum or AFHDS2A .
- Tue Dec 08, 2020 10:01 am
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 4539
Re: Jeti Duplex telemetry
Thank you kalle
- Mon Dec 07, 2020 4:55 pm
- Forum: openTx
- Topic: Jeti Duplex telemetry
- Replies: 6
- Views: 4539
Jeti Duplex telemetry
I have a Jeti module -the old one-, would it be possible to get and display the telemetry datas with OTX ?
MP
MP
- Sat Nov 21, 2020 1:16 pm
- Forum: Turnigy 9XR PRO radio
- Topic: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
- Replies: 189
- Views: 120574
Re: Banggood 4in1 module, Flysky AFHDS2A and Telemetry
Hi Mike,
In the OpenTx thread you will find a link given by Kilrah about the issue encountered by Hpnuts following 2A sensors.
In the OpenTx thread you will find a link given by Kilrah about the issue encountered by Hpnuts following 2A sensors.
- Thu Nov 19, 2020 12:05 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 4
- Views: 4322
Re: X8R burned regulator
Thanks Kalle, I did not know the matricule of this chip; unfortunately since some tracks are destroyed I need a regulatot with wires in order to solder two on the connector block and the third direct on the PCB. Regulator ordered at Ebay .
MP
MP
- Wed Nov 18, 2020 2:11 pm
- Forum: Hardware
- Topic: X8R burned regulator
- Replies: 4
- Views: 4322
X8R burned regulator
After a Bec failure I have a 3.3volts regulator burned; what chip I could purchase in TO92 case ?
Thanks
Thanks
- Wed Nov 18, 2020 8:21 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: AFHDS-2A telemetry
- Replies: 1
- Views: 2113
AFHDS-2A telemetry
The AFHDS-2A sensor range is not comprehensive; I would like a RPM BL sensor and a Amp sensor recognised by OTX, do you think it is possible with oXs ?
MP
MP
- Tue Nov 17, 2020 4:35 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 5309
Re: AFHDS-2A telemetry
Oupss, sorry Kilrah, I was wrong , I discovered the Alt sensor, and the atmospheric pressure!
Thanks for your help
MP
Thanks for your help
MP
- Tue Nov 17, 2020 2:27 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 5309
Re: AFHDS-2A telemetry
OK updated both OTX and module (STM32)....but no CAT01 sensor...
- Sat Nov 14, 2020 2:26 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 5309
Re: AFHDS-2A telemetry
OK, I changed the PC and now the Horus is flashed with the 2.3.10 FW but now it ask to update the multi-module, howto ? with Companion ? it is the 328 one.
- Sat Nov 14, 2020 12:26 pm
- Forum: openTx
- Topic: AFHDS-2A telemetry
- Replies: 9
- Views: 5309
Re: AFHDS-2A telemetry
I guess you tell "Tx off" ? When I do that I see the transfer is instantly on the PC screen....but the FW remain the same (2.2.1) I get the message Filter on vendor = 0x0483 product = 0xdf11 More than one DFU capable USB device found, you might try `--list' and then disconnect all but one ...