Search found 14 matches
- Wed Oct 05, 2016 9:47 pm
- Forum: er9x model setup
- Topic: Aileron differential with elevons ? Trim shift ?
- Replies: 1
- Views: 6787
Aileron differential with elevons ? Trim shift ?
Turnigy TGY 9x SUN : er9x-r762 VERS: V1. 5655-erez DATE: 14.05.2012 TIME: 20:50:26 continuation of elevons with knob to adjust servo travel ? SORTED http://openrcforums.com/forum/viewtopic.php?f=102&t=9241&p=119402#p119402 Flown the glider a few times, going close to ok. The trim shifts with...
- Thu Sep 29, 2016 10:45 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
I think the Key was my lack of Mixer understanding specifically what FULL would do, thanks.
- Thu Sep 29, 2016 10:25 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
it does, thank you
in case anyone else would like a similar setup for their 2 servo sloper
CH1
+25 ELE
+35 AIL
*100 CH8
CH2
-25 ELE
+35 AIL
*100 CH8
CH8
+35 P3 100 Offset
+30 FULL
Thanks again Mike and to all who contributed.
Regards Donald
in case anyone else would like a similar setup for their 2 servo sloper
CH1
+25 ELE
+35 AIL
*100 CH8
CH2
-25 ELE
+35 AIL
*100 CH8
CH8
+35 P3 100 Offset
+30 FULL
Thanks again Mike and to all who contributed.
Regards Donald
- Thu Sep 29, 2016 9:47 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
Brilliant Mike, works perfectly with the knob in the correct sense, Thank you.
Thanks Reinhard, I may try that down the track.
Thanks Reinhard, I may try that down the track.
- Thu Sep 29, 2016 5:20 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
I tried CH9 + 30 125 offset helped a little so servo travel now 10 to 70% turning P3 although knob was clockwise for less tried CH9 + -30 P3 -125 Offset to make P3 knob work in correct sense servo direction reverses at ~80% of P3 rotation tried +CH9 125% didn't make much difference any ideas on 'lif...
- Thu Sep 29, 2016 4:48 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
Thanks Mike Tried your set up mod using CH9 unfortunately it is still the same with servo travel at zero know full clockwise and a reduced servo travel with know full anticlockwise ( say 70%) I do not have a fix offset in the MIXER menu If I look at the top screen which displays each servo travel as...
- Wed Sep 28, 2016 9:41 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
"MikeB On channel 9 (say) set up 2 mixes: +35% P3 Offset(100%) +30% Max" Why can I not have just the second ADD mix on my existing setup? I wondered if I reduce the initial weight and have an ADD mix this 'holding up' the servo travel to a minimum of the 30% The question I have is how to p...
- Wed Sep 28, 2016 8:04 am
- Forum: er9x
- Topic: cordless trainer using rx mounted on the rear of the tx plugged into the trainer jack ?
- Replies: 1
- Views: 2359
cordless trainer using rx mounted on the rear of the tx plugged into the trainer jack ?
My apologies if this is in the wrong section Master tx turnigy tgy 9x slave tx HK HK6S I have a friend who is willing to help me and suggested it may need a transistor to invert the ppm pulse. H?e did this some time ago on a futaba 9z around 5+ years ago when I would teach chopper, worked a charm. H...
- Wed Sep 28, 2016 7:56 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
I've been playing with eppee and trying it on my tx
it seems I can not have say 50~100% servo via a knob, yet
how would you suggest maybe adding a mix that will not let the servo travel go below 50
%
it seems I can not have say 50~100% servo via a knob, yet
how would you suggest maybe adding a mix that will not let the servo travel go below 50
%
- Wed Sep 28, 2016 2:57 am
- Forum: er9x
- Topic: Trainer query
- Replies: 2
- Views: 2659
Re: Trainer query
Good point, will advise later.
- Wed Sep 28, 2016 2:55 am
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
Amazing response ! Thank you. Unfortunately at present I have no way of updating the software. I have considered installing the smartipants, this must wait a couple of months, due to finances and time. Therefore I was trying to set up the elevons with the current original software. It seems I am una...
- Tue Sep 27, 2016 1:29 pm
- Forum: er9x
- Topic: Trainer query
- Replies: 2
- Views: 2659
Trainer query
Turnigy TGY 9x SUN : er9x-r762 VERS: V1. 5655-erez DATE: 14.05.2012 TIME: 20:50:26 Hi I'm trying to use Turnigy 9x as master and HK6s as slave, doesn't work or Futaba skysport 4 as slave, doesn't work all 3 radios work on Pheonix, Realflight and XTR flight sim Also when trainer switch selected if I ...
- Tue Sep 27, 2016 1:16 pm
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
Re: elevons with knob to adjust servo travel ?
Tried altering P3 mix to the following 3 options weight 25 offset 75 and weight 10 offset 90 and weight 40 offset 60 I think this is most likely as I do not understand the mix math. All above still reduce servo travel to near zero at full anticlockwise of knob P3 I tried an additional mix to add wit...
- Tue Sep 27, 2016 12:10 pm
- Forum: er9x model setup
- Topic: elevons with knob to adjust servo travel ? SORTED
- Replies: 24
- Views: 21809
elevons with knob to adjust servo travel ? SORTED
Hi folks Flying wing 2 servos (elevons) I am running a stock tx purchased from HK ~1 year ago I have elevons working ok. I would like 2 options set up on separate model memories 1) a knob P3 to provide the ability to reduce the servo travel of both AIL and ELE 2) 2 knobs P1 to adjust ELE travel and ...