openrcforums

Hello Mike,
the program runs very well so that the erskyTx file could be entered on the er9x -erskyTx homepage.

greeingst Siegi

As far as I know, this module can only store one recipient. if you have a second recipient you have to tie it again and again.
a multi-protocol module provides a remedy
phil

hello Mike can the height sensor be seen on this file?

Hi Mike,
it took some time. I had to see how it works with the raw file.
logging with cat1 worked, I hope you can do something with the data. Greetings Siegi

Hi Mike,
in october last year we had contact about the height sensor cat01. We couldn't activate it at the time and display the altitude.
In the new TX16S with the latest software, the transmitter shows the altitude with opentx, but not with erskyTx. what can be the reason?
greetings Siegi

attached are the screens with erskyTX.
LS and RS do not run in parallel

Thanks for the information. I noticed that with the A9r 223 software the RS signal was lost. The error was eliminated in the B3r 223 software. the slider direction RS should be reversed so that when the button points upwards the bar also deflects upwards. For the optics, it would be nice if some dis...

there is always something new for me. Suddenly the power lamp from the Radiomaster shows "green" and not red. Firmware: erskyTx is from March 19, so the latest version. What has changed?
that's great!

Hi Mike,
I noticed that the two lateral rotary valves SL and SR do not run synchronously. I've tried a lot but haven't made it. Do you have a guy there?
lovely Easter Phil

There are things that one does not understand. before I could restart the transmitter I removed the erskyTx programs from the SD card. after the restart I loaded again via eePskye erskyTx. There is no erskyTx on the bootloader, and there is no erskyTx on the SD card either, although I operate the tr...

Hi Mike,
my joy in experimenting is a little clouded. for me the software 223A9 in color with logical key assignment would be sufficient. This software is clear and quick to adapt and easy to use.
thank you phil

studying the video of bardwell, radiomaster bricked. 1. PC with driver for DFU, impulseRC 2. Transmitter without battery 3. Connection of PC to transmitter 4. loaded with companion software opentx Very important The transmitter must be without a battery, no success with the battery connected. it too...

he is working again, has cost nerves!
i am happy

unfortunately I was unable to repair the transmitter. i watched help videos and tried everything.
the fault is probably in the motherboard.

i was in opentx

i make one video phil

Hy Mike

I checked and made it straight away. STM bootloader was always available.
The transmitter is "dead" no power lamp!
Presumably a case for warranty, I submitted. Let's see what comes out. I suspect the roller blacked out

phil

I hit enter with the roller and suddenly the screen went black. Power on does not work anymore, only the above characters are flashing. the power light does not burn at all anymore. When I let go of the power button, the blinking of the characters has gone out. I have contact to the bootloader via t...

I'm devastated, when I tried to update the bootloader, the transmitter destroyed itself, switched itself off and is only black. Switching on is not possible!

I can't save the 2nd screen. back in the menu the screen no longer appears. but he is in Popoups! I can call up the erskyTx software with the bootloader, but the install command is not accepted. the arrow is also not shown in full and flickers. So via PC! of the different versions only the last one ...

Hi Mike, the last software works perfectly. I was only able to bring an additional screen into the main menu, however. I was able to create the 2nd screen but it was not recorded. what I am still missing are the pictures of the planes (image). there is no connection to opentx. my favorite is still t...

Hello Mike, I'm back. in the meantime many have downloaded tx16. has there been any feedback? I wish: . Reduce channel flicker= importand . Equip version A9r223 with color .version A9r223 with side button symbols(taranis 9d) left side:button 1 M=menue(sys) 2 X=back 3 arrow ↑ 4 arrow ↔ 5 arrow ↓ righ...

No! Detected with flashlight display and on setting radio setup and found the switch, sa pressed and it was bright. Brightness to 64 and it works. the main screens are not yet consistent, numbers and symbols are of different sizes and interfere with each other. the smaller version is better Another ...

good morning Mike, I wanted to test the buttons with yesterday's "colored" software tx16_rom.bin. I could not load this software anymore !eePskye works good and say sucessful, the screen was black. has this software changed something in the transmitter? software A9 223 runs fine. greetings...

the problem: roller. in A9 223 work roller good, in the software today no good, going diplay black when change switch!!
please Rollerupdate back

the new button setting was also pleasant. one would have to practice longer to recognize the advantage.
if the scooter works properly I would install the "colored software"

Hi Mike, I made it, the USB plug was not tight. the new software works very well, buttons work. a big problem arose when I want to change the light switch in radio setup the screen goes black. I have to flash again! no longer works!! the screen remains black. re-flashing is not possible, stays black...

good morning mike, Thanks for the new software. I could not load the new software with eePskye! to make sure that everything is correct I activated eePskye again. it did not work! I didn't want to load with CompanionTX. The reason is that tx16s A9 223 works well with scooter and push-open. Sorry tha...

SYS =Menue
RTN =Exit

MDL =Model select
left side: SyS, RTN, PAge, Page,Tele
right side: MDL, Roller and run