Search found 9 matches
- Fri May 13, 2016 5:07 pm
- Forum: 9Xtreme upgrade board
- Topic: PPM and the 9xtreme
- Replies: 20
- Views: 11442
Re: 9xtreme X8R + XJT = NAZA
Need help to setup a 9xtreme + X8R rx + XJT tx and NAZA. Installed a XJT module ans a X8R in replacement of a DJT with V8FR-II. SET jumpers to CH1-2 and CH3-4, the 2 switches on XJT are off. I should be in mode 4. The bind is OK. Sbus connected to NAZA X2 (the only cnx to the naza board). After chan...
- Fri Jan 22, 2016 11:06 am
- Forum: er9x
- Topic: How to set up 16ch Tx with er9x!
- Replies: 86
- Views: 61348
Re: How to set up 16ch Tx with er9x!
Hi Tech1uk, Great to read somebody got 16 channels implementing an easy set of componenets (1 x XJT and 2 x X8R). I still need to get confirmation on the following: Q1 ? how do you wire XJT to get the telemetry back on your radio screen (Turnigy 9X + 9Xtreme) ? Q2 ? does X8R and V8R can work togethe...
- Thu Jan 21, 2016 9:33 pm
- Forum: er9x
- Topic: How to set up 16ch Tx with er9x!
- Replies: 86
- Views: 61348
Re: How to set up 16ch Tx with er9x!
thx Mike, I ll investigate and will do my best to understand all. I ll be back if something looks strange to me.
B rgds - Thierry (BE)
B rgds - Thierry (BE)
- Thu Jan 21, 2016 5:47 pm
- Forum: er9x
- Topic: How to set up 16ch Tx with er9x!
- Replies: 86
- Views: 61348
Re: How to set up 16ch Tx with er9x!
Hi, I have read all posts from this subject down to 2011(16ch with ER9X). Also read the manuel for the 9XR PRO. Very interesting discussions. Unfortunatly too much technical details for me or for the objectif I am trying to reach. The objectif: have 16ch & telemetry on a Turnigy 9X with the 9xtr...
- Fri Jan 15, 2016 5:15 pm
- Forum: Software
- Topic: 9xtreme smartiepart
- Replies: 2
- Views: 2400
Re: 9xtreme smartiepart
Thx for the openrcforums sortcut. Magic, too simple when you know how to ;-). Many many thnks for your help. Confidence is coming back. The read memory does not work under WIN10 64. It works under WIN7 64bits. I have successfully transferred my models from the V2.4 board to the 9xtreme. Still have t...
- Fri Jan 15, 2016 3:45 pm
- Forum: 9Xtreme upgrade board
- Topic: Tx Disk Not Mounted
- Replies: 10
- Views: 12500
Re: Tx Disk Not Mounted
had same discovery path than "blackgun". I finally found the trim trick. I can see the 2 disks. When trying to load my models exported from another turnig9x with the v2.4 board, i am still receiving the "tx disks not mount" error msg. I have most probably missed something. In det...
Re: eepe v420/v419 and 9extreme board
I have on a TURNIGY9x the v2.4 board from smartiepart. I have exported my models and try to flash onto another Turnigy 9x with the 9xtreme board installed . Unfortunatly I cannot get a usb connexion to the 9xtreme board. EEPE works perfect with the V2.4 board. Where is the trick ? HELP. When I conne...
- Tue Jan 12, 2016 5:25 pm
- Forum: Software
- Topic: newst stable ERSky9X firmware
- Replies: 3
- Views: 3512
Re: newst stable ERSky9X firmware
Hi airtime, did you succeed to read the firmware installed.
Perso I cannot get a usb connexion. I have read that a specific sequence of action is required to see the sd content etc....
any idea. Thx u before hand for an advice - Thierry
Perso I cannot get a usb connexion. I have read that a specific sequence of action is required to see the sd content etc....
any idea. Thx u before hand for an advice - Thierry
- Tue Jan 12, 2016 5:22 pm
- Forum: Software
- Topic: 9xtreme smartiepart
- Replies: 2
- Views: 2400
9xtreme smartiepart
Hi, Sounds appropriate to start a topic on the lastest Smartiepart board the 9xtreme. I am writing about the board with new cpu, voice/sound, and SD card. I have installed it, created manually a model (TBS450 for info), made a test flight, It works. Where is the best place to read information or doc...