openrcforums

When is it necessary to change the regulator? I have the Smartiparts board with back light, the TelemetrEZ, the internal FrSky module, the haptic mod and in a short time the Taranis gimblas with amplifier. Is the standard regulator still okay for that or already on the knifes edge?

Bob, have you checked the ribbon cable from the PCB to the display, or its connector?

Thank you Bob for this Information. So I think the ground fix is easy to do while changing the gimbals.
For the power mod: Is THIS a right one for it?

Aaaah... I see it now, too... Thank you. Then I see no need for me to modify the sticks mechanically.

Is it already in the official r809?

Isn't it sufficient to Change in er9x the "Throttle reverse" when using Mode 2?

lebenj wrote:There is a machanical solution to reverse the pots!very easy. If for example you use open9X and you don't have the software reverse solution!

Have you to make this mod (or stick reversion in firmware) for both direction of this stick (i.e. pitch and rudder)?

Im terribly sorry :( :( :( :D No issue... i use my 9X and 2 taranis gimball without any problem... and i have also the back light! With the amplified ones? Taranis Gimbals: #1 Red wire to Black wire 9x Radio Taranis Gimbals: #2 Orange wire to White wire 9x Radio Taranis Gimbals: #3 Brown wire to Re...

Only ordered one week later than Joao...

Received my gimbals today. Can anyone see if it is with or without amp?

Thanks for the info. I think I will also order a pair at aloft then. I hope it is worth the money and time.

Edit: *ORDERED*

bob195558 wrote: Also was the Taranis Gimbals from Aloft Hobbies the un-amplified 5k Potentiometers?

That would interest me, too!

jhsa wrote:Will see here.
The most I would pay would be 19% I think.

When the value of the goods is less than 22€ you don't have to pay 19%. USA shipments are usually very fast and quicker through the customs than shipments from Asia.

I think we are now a Little bit of Topic...

jhsa wrote:Still cheaper from aloft..

...I see...

Have already taken a look here? Engel

Edit:

Or here: EMT

Just for my understanding: Do the amplified sticks not work in the 9X, while the unamplified do?

Okay, here we go... it should work now.
For everyone who need it. I have tried it to make it as exact as I could.

Screen as dxf and dwg

How can I upload files here? When I try to link files from google drive, my complete post will be deleted.
I wanted to upload the screen as CAD files in dwg and dxf.

For everyone who is interested in a CAD drawing of the screen: Here is it in dwg and dxf file.

Display as dwg
Display as dxf

Those I made were printed as mirror image on clear vinyl and back sprayed with white rattle can spray. Then when stuck on the backside of the screen they are not mirror. Thank you for your help so far. A last question (I hope :mrgreen: ): How did you stick the vinyl on the back and the screen back ...

Those I made were printed as mirror image on clear vinyl and back sprayed with white rattle can spray. Then when stuck on the backside of the screen they are not mirror. On a NEW display screen (self made / laser cut etc..) ? Or on the original one? And when on the original: How to get rid of the e...

Thank you for sharing your work NSF . The new paint job was neat, but your labels really set it apart. I simply printed these on Avery labels, and then covered them with packing tape. Cut them out with a razor, and stuck them on. Very simple, yet makes a big difference. Thanks Again. http://openrcf...

Short, stupid question: When I order the gimbals at t9hobbysport.com, is it only ONE or a pair of gimbals? Have I to order one or 2 pcs?

Found out today that it wasn't the antenna of the RX. Today it shows again some values that are far off reality. Sometime it shows right values, sometimes I have the feeling it is counting up. In one flight it has shown up to 16.000 rpm.... begining from 2.000... really don't know what it is.

Okay guys, I have just found out today that the abnormal values from the RPM are a result from the antenna, which was parallel on a length for about 1 or 2 inches with zip ties with the wire from the RPM. I have rerouted the antenna position and now the RPM works like before. ( I don't know why othe...

I have the latest Firmware on the tez. Before 801 it has worked fine, and headspeed was correct (tested with an optical hand rpm-meter) I am wodering about the wide range it is measuring wrong now (between 4000 and 9000 randomly) Could it be a problem with an antenna which is close to a part of the ...

RPM01 from Frsky. And yes, FBL (Tarot)

I am flying a Rex 550 with sensor hub plugged in T1, T2, RPM, FLVS, FAS100

I was out today and flying with 801.
The undefined warnings for T2 are still there, but now the RPM shows only unreal numbers. Before it shows the real rpm of about 2000 and now it shows something between 6000 and 9000! ! ! No. of blades ist still 2.

I am using er9x.
The hub is V2.
Normal value on T2 is something about 40 to 60. Abnormal values are about 2000 or more (Maybe it is over 20.000). Don't know, because it is a very short time. Hard to see while flying. Sometimes it is long enough to activate the alarm one time, sometimes not.