Turnigy 9X 9Ch / 16 channels?
Turnigy 9X 9Ch / 16 channels?
hello,
can you tell me whether the Turnigy 9X 9Ch works with 16 channels or not.
Meanwhile, I have a wide variety of information from the German forums. But either it does not work or I can’t make it work. My English is not good.
I hereby try:
Turnigy 9x 9Ch Transmitter
open TX-r2940
Turnigy RF9X-V2 module
6 piece Turnigy 9X8C-V2 8-channel receiver
Can I then work with 16 channels? If so, what should I do, that it works. Or should I replace the module. What can I take, I would like to keep the old receiver. I need 16 channels for only 2 ships, for the rest less than 8 would be enough.
Thanks and greeting
Dirk
can you tell me whether the Turnigy 9X 9Ch works with 16 channels or not.
Meanwhile, I have a wide variety of information from the German forums. But either it does not work or I can’t make it work. My English is not good.
I hereby try:
Turnigy 9x 9Ch Transmitter
open TX-r2940
Turnigy RF9X-V2 module
6 piece Turnigy 9X8C-V2 8-channel receiver
Can I then work with 16 channels? If so, what should I do, that it works. Or should I replace the module. What can I take, I would like to keep the old receiver. I need 16 channels for only 2 ships, for the rest less than 8 would be enough.
Thanks and greeting
Dirk
Re: Turnigy 9X 9Ch / 16 channels?
The stock module can't transmit more than 8 channels.
One way is to add a second module connected to the trainer port, might be the most appropriate for your situation.
Another is to use an FrSky XJT which will transmit up to 12 or 16 channels depending on the operation mode, but then none of your current receivers will be useable.
One way is to add a second module connected to the trainer port, might be the most appropriate for your situation.
Another is to use an FrSky XJT which will transmit up to 12 or 16 channels depending on the operation mode, but then none of your current receivers will be useable.
Re: Turnigy 9X 9Ch / 16 channels?
I am not sure about openTX, it has been a while since I last used it, but with er9x you can connect another 8 channel RF Module to the trainer port.. You will have to select "PPM16" as protocol. The radio will then send channels 9 to 16 on the trainer port. Then you bind one receiver to the normal module that is in the module bay, and another receiver to the module connected to the trainer port..
João
EDIT: Kilrah was faster than me and confirmed that it also works in openTX
João
EDIT: Kilrah was faster than me and confirmed that it also works in openTX
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Turnigy 9X 9Ch / 16 channels?
Get one of these for the second eight channels
http://www.ebay.de/itm/261154202998?ssP ... 1436.l2648
Reinhard
http://www.ebay.de/itm/261154202998?ssP ... 1436.l2648
Reinhard
Re: Turnigy 9X 9Ch / 16 channels?
Hello Reinhard,
how and where do I connect to?
In addition to the existing module?
Greetings Dirk
how and where do I connect to?
In addition to the existing module?
Greetings Dirk
Re: Turnigy 9X 9Ch / 16 channels?
As said above, using it as the second rf module via the trainer port. And the pin layout is well known, as it is already used in the primary RF module.
I would remove the Pcb and place it somewhere in the radio housing.
Reinhard
I would remove the Pcb and place it somewhere in the radio housing.
Reinhard
Re: Turnigy 9X 9Ch / 16 channels?
Hello Reinhard,
there for the conversion instructions (for the not so experienced )
Greetings Dirk
there for the conversion instructions (for the not so experienced )
Greetings Dirk
-
- Posts: 3
- Joined: Tue Aug 19, 2014 6:39 pm
- Country: -
Re: Turnigy 9X 9Ch / 16 channels?
I've read through this thread and it is something that I would like to do soon, but has someone made a schematic on how to wire it all up?
Re: Turnigy 9X 9Ch / 16 channels?
Hi guys. I have replaced the original RF unit with a djt module and a new compatible receiver on my 9X radio. This gives me 8 channels. Is there anyway the I can use the original RF module and the stock receiver so I can add a few more channels to my 9x radio?
- MikeB
- 9x Developer
- Posts: 17994
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9X 9Ch / 16 channels?
Not on the original 9X, it can only support a single module.
All I can suggest is a XJT module, as that supports 16 channels to either 2 'X' receivers, or a single 'X' receiver using the SBUS output for the extra channels.
Mike
All I can suggest is a XJT module, as that supports 16 channels to either 2 'X' receivers, or a single 'X' receiver using the SBUS output for the extra channels.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9X 9Ch / 16 channels?
OpenTX allowed connecting a 2nd module to the trainer port and sending upper channels to it. I think it was the "PPM16" choice.
- MikeB
- 9x Developer
- Posts: 17994
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9X 9Ch / 16 channels?
I forgot that, PPM16 is in er9x as well (I wrote it!).
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9X 9Ch / 16 channels?
So considering the fact that my radio uses er9x firmare it is doable with 2 RF units. How would I go about connecting them? Is there a how to somewhere?
- MikeB
- 9x Developer
- Posts: 17994
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9X 9Ch / 16 channels?
You would need to connect the trainer jack socket (ground and signal) to the ground and signal of the second module, and provide power to the second module somehow.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9X 9Ch / 16 channels?
Thanks Mike.
Re: Turnigy 9X 9Ch / 16 channels?
I remember tried the TH9X with a Jeti and Orange module working fine with 12 ch.Rxs