Search found 19 matches
- Tue Dec 08, 2020 4:10 pm
- Forum: ersky9xr
- Topic: CRSF protocol for TBS Crossfire?
- Replies: 225
- Views: 195995
Re: CRSF protocol for TBS Crossfire?
I went through and remapped the mixer channels for the switches and they seem to be working now
- Tue Dec 08, 2020 2:50 pm
- Forum: ersky9xr
- Topic: CRSF protocol for TBS Crossfire?
- Replies: 225
- Views: 195995
Re: CRSF protocol for TBS Crossfire?
What is the correct firmware that I should be on? I have been pulling from the test version page.
- Sun Dec 06, 2020 8:51 pm
- Forum: ersky9xr
- Topic: Turnigy 9xr pro voice problem
- Replies: 16
- Views: 16357
Re: Turnigy 9xr pro voice problem
I will have to flash the firmware back to ersky9xr, as right now I flashed the opentx version for the 9xr pro to get crossfire working. I'm trying to figure out why opentx is not saving the models to the sdcard.
- Sun Dec 06, 2020 8:34 pm
- Forum: ersky9xr
- Topic: CRSF protocol for TBS Crossfire?
- Replies: 225
- Views: 195995
Re: CRSF protocol for TBS Crossfire?
I got the Crossfire Micro module finally and all i can get working are the first 4 channels. its not seeing any of my switches. all i did was change the protocol in the protocol menu to crsf from dsm. What am i missing. For the time being i flashed my 9xr pro over to the opentx version that supports...
- Fri Nov 06, 2020 8:10 pm
- Forum: ersky9xr
- Topic: CRSF protocol for TBS Crossfire?
- Replies: 225
- Views: 195995
Re: CRSF protocol for TBS Crossfire?
I have been reading through this and are my assumptions correct that crossfire is working on the 9XR PRO? I am about to order the micro module for long range flying. I have updated to the latest firmware ersky9x-A4r223.
- Mon Nov 02, 2020 6:35 pm
- Forum: ersky9xr
- Topic: Turnigy 9xr pro voice problem
- Replies: 16
- Views: 16357
Re: Turnigy 9xr pro voice problem
I have a 9xr pro that never made any sound from the beginning when using the trims. I have never been able to get he voice working. I have updated it to the latest version ersky9x-A4r223. I got the radio when hobby king first launched them. I have opened it to make sure the speaker was connected and...
- Tue Jul 17, 2018 5:45 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
After taking some measurements with my meter, the 3.3v reg and the xmega are fried. time to order another module lol
- Tue Jul 17, 2018 4:18 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
And... somehow I cooked the 3.3v regulator on the module.I have another regulator floating around somewhere so I might replace it,
- Tue Jul 17, 2018 2:42 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
Yes I did power the board through the 5 pin connector from the radio while I flashed it.
- Tue Jul 17, 2018 2:20 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
I am going to bust out the soldering iron and start over and try flashing the bootloader with the pro mini instead of flashing it with the Tx.
- Tue Jul 17, 2018 2:00 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
I am still trying to find where the two missing resistors are that I need to solder a jumper across
- Tue Jul 17, 2018 1:59 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
i was careful but did end up lifting the pads. Do those traces run to another component? So far it looks like they just run to the other side of the board to a pad that is not connected to anything but I don't know if there is a layer in the middle of the board.
- Tue Jul 17, 2018 1:39 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
MultiOrangeBoot.bin is the file I used. The firmware i used in the Tx is ersky9xProvR222b4.
- Tue Jul 17, 2018 12:20 pm
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
I tried the com port both ways, along with holding the bins button while booting. I have also watched the led to see what it does while booting and it does not flash either, in fact it does not even light up. I am suppoased to be using the file for the green board correct?
- Tue Jul 17, 2018 3:45 am
- Forum: RF MODULES
- Topic: Orange Module running MULTI protocol
- Replies: 685
- Views: 433385
Re: Orange Module running MULTI protocol
I have been trying to flash the multi firmware on my module all day. My Tx is the Turnigy 9XR Pro, and I have updated the firmware on it to enable flashing from the Tx. The module I have is the one on the second page, 8th post. I cut the trace and ran the telemetry wire. I was successfully able to f...
- Thu Mar 26, 2015 4:29 pm
- Forum: eePe
- Topic: EEPE and 9XR PRO
- Replies: 9
- Views: 14279
Re: EEPE and 9XR PRO
Is there anyway this can be stickied for others in the future. Hi, welcome to the forum.. You have to use eepskye with the 9XR-PRO.. The PRO uses the ersky9x firmware. eepe is to be used with er9x that comes installed with the old 9XR (Not PRO) Please go to eepe's installation folder, find "eep...
- Thu Mar 26, 2015 4:27 pm
- Forum: eePe
- Topic: EEPE and 9XR PRO
- Replies: 9
- Views: 14279
Re: EEPE and 9XR PRO
I found the eepskye and that worked like a charm. The transmitter connected right away and had no issues reading the memory or flashing the updated firmware. Thank you very much for the help.
Now I only need to learn all the advanced programing features
Now I only need to learn all the advanced programing features
- Thu Mar 26, 2015 3:56 am
- Forum: eePe
- Topic: EEPE and 9XR PRO
- Replies: 9
- Views: 14279
Re: EEPE and 9XR PRO
Thank you that worked perfectly
- Thu Mar 26, 2015 2:32 am
- Forum: eePe
- Topic: EEPE and 9XR PRO
- Replies: 9
- Views: 14279
EEPE and 9XR PRO
I am trying to backup models and write models to my radio via EEPE. I have the 9XR PRO not the 9XR. I know how to hold the aileron and rudder trim tabs to bring up the bootloader. Then plug in the usb cord to the usb port on the 9XR Pro. EEPE will not communicate with my radio. I have included a scr...